EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface roughness, stainability, and translucency of an additively manufactured interim resin reinforced with a commercially available ceramic composite concentrate after coffee thermal cycling

Mustafa Borga Donmez iD, Nicolas Michel Rotter, Gabriela Panca Sabatini iD, Almira Ada Diken Türksayar iD, Hyung-In Yoon iD, Burak Yilmaz iD

Journal of Prosthodontics · 16.04.2026

DOI: 10.1111/jopr.70131 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 16.04.2026. Verfasst von Mustafa Borga Donmez und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey. Die Arbeit nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To compare the surface roughness (R a ), stainability, and translucency of a ceramic composite concentrate‐reinforced interim resin with its corresponding non‐reinforced formulation and with a ceramic‐filled resin indicated for definitive use after coffee thermal cycling. Materials and Methods Disk‐shaped specimens (Ø10 × 1 mm) were additively manufactured from an unfilled resin for interim use (AM‐INT; FREEPRINT Temp, Detax), the same resin for interim use reinforced with a 30 wt% commercially available ceramic composite concentrate (AM‐R‐INT), and a ceramic‐filled resin indicated for definitive use (AM‐DEF; Crowntec, Saremco Dental AG) ( n = 12). The R a values of each specimen were measured before and after polishing. Color coordinates were measured after polishing, followed by 10,000 cycles of coffee thermal cycling, after which both R a and color measurements were repeated. The color difference (∆E 00 ) caused by coffee thermal cycling and the relative translucency parameter (RTP) of each specimen were calculated. The R a and RTP data were analyzed with a generalized linear model, while ∆E 00 values were evaluated with Kruskal–Wallis and Bonferroni‐corrected post hoc tests ( α = 0.05).

Results

The interaction between the resin type and time point significantly affected the R a and RTP, while the resin type impacted the ∆E 00 ( p ≤ 0.015). AM‐INT had the highest R a among the other resins before polishing, and the R a of each tested resin was higher before polishing than after polishing or coffee thermal cycling ( p ≤ 0.006). AM‐R‐INT had higher ∆E 00 than AM‐DEF ( p < 0.001). AM‐DEF had higher RTP than AM‐INT after polishing ( p = 0.006). However, AM‐DEF also had the lowest RTP after coffee thermal cycling, whereas AM‐INT had the highest ( p ≤ 0.018). AM‐R‐INT and AM‐DEF had reduced RTP after coffee thermal cycling ( p ≤ 0.001).

Conclusions

All tested resins achieved clinically acceptable R a after polishing and coffee thermal cycling. AM‐DEF exhibited a perceptible but clinically acceptable color change, whereas the other resins showed moderately unacceptable changes, highlighting potential esthetic limitations. The reinforced interim resin (AM‐R‐INT) exhibited a perceptible translucency difference compared with other resins after polishing, and coffee thermal cycling caused a significant reduction in translucency for both AM‐R‐INT and AM‐DEF, resulting in clinically unacceptable changes. These findings emphasize the importance of considering both material composition and polishing procedures when selecting interim and definitive prostheses, particularly for patients with regular exposure to coffee.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingceramic composite concentratefixed dental prosthesesstainabilitysurface roughnesstranslucency

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey.
  • Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Department of Advanced Digital Dental Technology, Biruni University Advanced Technology and Research Center (BAMER), Biruni University, Istanbul, Turkey.
  • Department of Prosthodontics, School of Dentistry and Dental Research Institute, Seoul National University, Seoul, Republic of Korea.
  • Department of Restorative, Preventive and Pediatric Dentistry, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Division of Restorative and Prosthetic Dentistry, The Ohio State University, Columbus, Ohio, USA.

ORCID-Profile: Mustafa Borga Donmez, Gabriela Panca Sabatini, Almira Ada Diken Türksayar, Hyung-In Yoon, Burak Yilmaz

Zitieren

APA

Donmez, M. B., Rotter, N. M., Sabatini, G. P., Diken Türksayar, A. A., Yoon, H. I., & Yilmaz, B. (2026). Surface roughness, stainability, and translucency of an additively manufactured interim resin reinforced with a commercially available ceramic composite concentrate after coffee thermal cycling. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70131

Vancouver

Donmez MB, Rotter NM, Sabatini GP, Diken Türksayar AA, Yoon HI, Yilmaz B. Surface roughness, stainability, and translucency of an additively manufactured interim resin reinforced with a commercially available ceramic composite concentrate after coffee thermal cycling. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70131

BibTeX
@article{Donmez2026,
  author = {Donmez, Mustafa Borga and Rotter, Nicolas Michel and Sabatini, Gabriela Panca and Diken Türksayar, Almira Ada and Yoon, Hyung-In and Yilmaz, Burak},
  title = {Surface roughness, stainability, and translucency of an additively manufactured interim resin reinforced with a commercially available ceramic composite concentrate after coffee thermal cycling},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70131}
}
Kostenlos starten →