EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface roughness, optical properties, and microhardness of additively and subtractively manufactured CAD‐CAM materials after brushing and coffee thermal cycling

Gülce Çakmak iD, Mustafa Borga Donmez iD, Marcella Silva de Paula, Canan Akay iD, Manrique Fonseca iD, Çiğdem Kahveci iD, Samir Abou-Ayash iD, Burak Yilmaz iD

Journal of Prosthodontics · 2025-01 · 34 (1) · 68-77

DOI: 10.1111/jopr.13796 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 27.11.2023. Verfasst von Gülce Çakmak und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland. Hauptthemen laut MEDLINE: Coffee, Computer-Aided Design, Toothbrushing, Dental Materials. Die Arbeit wurde bisher 49-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the surface roughness, optical properties, and microhardness of additively or subtractively manufactured CAD‐CAM materials after simulated brushing and coffee thermal cycling. Material and methods Two additively manufactured resins (Crowntec, CT and VarseoSmile Crown Plus, VS) and 3 subtractively manufactured materials (a reinforced composite (Brilliant Crios, BC), a polymer‐infiltrated ceramic network (Enamic, VE), and a feldspathic ceramic (Mark II, VM)) were used to fabricate disk‐shaped specimens (Ø10×1‐mm) ( n = 10). Surface roughness, Vickers microhardness, and color coordinates were measured after polishing, while surface roughness was also measured before polishing. Specimens were then subjected to 25000 cycles of brushing and 10000 cycles of coffee thermal cycling, and measurements were repeated after each time interval. Color difference (ΔE 00 ) and relative translucency parameter (RTP) were calculated. Robust analysis of variance test was used to evaluate surface roughness, ΔE 00 , and RTP data, while generalized linear model analysis was used for microhardness data (α = 0.05).

Results

Material type and time interval interaction affected tested parameters ( p ≤ 0.002). In addition, material type affected all parameters ( p < 0.001) other than surface roughness ( p = 0.051), and time interval affected surface roughness and microhardness values ( p < 0.001). Tested materials mostly had their highest surface roughness before polishing ( p ≤ 0.026); however, there was no clear trend regarding the roughness of materials within different time intervals along with ΔE00 and RTP values within materials or time intervals. VS and CT had the lowest microhardness regardless of the time interval, while the remaining materials were listed as VM, VE, and BC in decreasing order ( p < 0.001). Coffee thermal cycling only reduced the microhardness of VM ( p < 0.001).

Conclusions

Tested additively manufactured resins can be considered more susceptible to simulated brushing and coffee thermal cycling than the other materials, given the fact that their surface roughness and ΔE00 values were higher than previously reported acceptability thresholds and because they had the lowest microhardness after all procedures were complete.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CoffeeComputer-Aided DesignToothbrushingDental MaterialsDental Prosthesis DesignSurface PropertiesHardnessMaterials TestingComposite ResinsCeramicsCrownsColorHumansDental Porcelain

Stichwörter der Autor:innen

additive manufacturingbrushingcoffee thermal cyclingroughnessstainabilitytranslucency

Substanzen

CoffeeComposite ResinsDental MaterialsDental Porcelain

Autor:innen und Institutionen

  • Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Department of Prosthodontics, Faculty of Dentistry, Istinye Univeristy, İstanbul, Turkey.
  • Department of Prevention and Oral Rehabilitation, Universidade Federal de Goiás, Goiánia, GO, Brazil.
  • Department of Prosthodontics, Faculty of Dentistry, Eskisehir Osmangazi Univeristy, Eskisehir, Turkey.
  • Translational Medicine Research and Clinical Center, Osmangazi University, Eskisehir, Turkey.
  • Ordu Oral and Dental Health Center, Ordu, Turkey.

ORCID-Profile: Gülce Çakmak, Mustafa Borga Donmez, Canan Akay, Manrique Fonseca, Çiğdem Kahveci, Samir Abou-Ayash, Burak Yilmaz

Zitieren

APA

Çakmak, G., Donmez, M. B., de Paula, M. S., Akay, C., Fonseca, M., Kahveci, Ç., Abou-Ayash, S., & Yilmaz, B. (2025). Surface roughness, optical properties, and microhardness of additively and subtractively manufactured CAD‐CAM materials after brushing and coffee thermal cycling. Journal of Prosthodontics, 34(1), 68-77. https://doi.org/10.1111/jopr.13796

Vancouver

Çakmak G, Donmez MB, de Paula MS, Akay C, Fonseca M, Kahveci Ç, et al. Surface roughness, optical properties, and microhardness of additively and subtractively manufactured CAD‐CAM materials after brushing and coffee thermal cycling. Journal of Prosthodontics. 2025;34(1):68-77. doi:10.1111/jopr.13796

BibTeX
@article{akmak2025,
  author = {Çakmak, Gülce and Donmez, Mustafa Borga and de Paula, Marcella Silva and Akay, Canan and Fonseca, Manrique and Kahveci, Çiğdem and Abou-Ayash, Samir and Yilmaz, Burak},
  title = {Surface roughness, optical properties, and microhardness of additively and subtractively manufactured CAD‐CAM materials after brushing and coffee thermal cycling},
  journal = {Journal of Prosthodontics},
  year = {2025},
  volume = {34},
  number = {1},
  pages = {68--77},
  doi = {10.1111/jopr.13796}
}
Kostenlos starten →