EUVIMEDEUVIMED entdecken
Crossref

Surface roughness and shear bond strength to composite resin of additively manufactured interim restorative material with different printing orientations

Leila Nasiry Khanlar, Marta Revilla-León, Abdul Basir Barmak, Masaomi Ikeda, Qutaiba Alsandi, Junji Tagami, Amirali Zandinejad

The Journal of Prosthetic Dentistry · 2023-05 · 129 (5) · 788-795

DOI: 10.1016/j.prosdent.2021.08.010 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023-05. Verfasst von Leila Nasiry Khanlar und 6 weiteren Autor:innen. Beteiligte Einrichtung: PhD Candidate, Department of Cariology and Operative Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, …. Hauptthemen laut MEDLINE: Dental Bonding. Die Arbeit wurde bisher 38-mal zitiert (Crossref) und nennt 52 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Additive manufacturing (AM) is a technology that has been recently introduced into dentistry for fabricating dental devices, including interim restorations. Printing orientation is one of the important and influential factors in AM that affects the accuracy, surface roughness, and mechanical characteristics of printed objects. However, the optimal print orientation for best bond strength to 3D-printed interim restorations remains unclear. PURPOSE: The purpose of this in vitro study was to evaluate the effect of printing orientation on the surface roughness, topography, and shear bond strength of AM interim restorations to composite resin. MATERIAL AND METHODS: Disk-shaped specimens (Ø20×10 mm) were designed by a computer-aided design software program (Geomagic freeform), and a standard tessellation language (STL) file was obtained. The STL file was used for the AM of 60 disks in 3 different printing orientations (0, 45, and 90 degrees) by using E-Dent 400 C&B material. An autopolymerizing interim material (Protemp 4) was used as a control group (CNT), and specimens were fabricated by using the injecting mold technique (n=20). Surface roughness (Sa, Sz parameters) was measured by using a 3D-laser scanning confocal microscope (CLSM) at ×20 magnification. For shear bond testing, the specimens were embedded in polymethylmethacrylate autopolymerized resin (n=20). A flowable composite resin was bonded by using an adhesive system. The specimens were stored in distilled water at 37 °C for 1 day and thermocycled 5000 times. The shear bond strength (SBS) was measured at a crosshead speed of 1 mm/min. The data were analyzed by 1-way ANOVA, followed by the Tukey HSD test (α=.05). RESULTS: The 45-degree angulation printing group reported the highest Sa, followed by the CNT and the 90-degree and 0-degree angulations with significant difference between them (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental BondingMaterials TestingDental MaterialsComposite ResinsPolymethyl MethacrylatePrinting, Three-DimensionalSurface PropertiesShear StrengthResin Cements

Substanzen

Dental MaterialsComposite ResinsPolymethyl MethacrylateResin Cements

Autor:innen und Institutionen

  • PhD Candidate, Department of Cariology and Operative Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • Affiliate Assistant Professor, Graduate Prosthodontics, Department of Restorative Dentistry, School of Dentistry, University of Washington, Seattle, Wash and Faculty and Director of Research and Digital Dentistry, Kois…
  • Assistant Professor of Clinical Research and Biostatistics, EIOH Medical Center, University of Rochester, Rochester, NY.
  • Senior Lecturer, Oral Prosthetic Engineering, Graduate School, Tokyo Medical and Dental University, Tokyo, Japan.
  • Professor, Department of Cariology and Operative Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
  • Associate Professor with Tenure and Program Director AEGD Residency Program, College of Dentistry, Texas A&M University, Dallas, Texas. Electronic address: azandinejad@tamu.edu.

Zitieren

APA

Nasiry Khanlar, L., Revilla-León, M., Barmak, A. B., Ikeda, M., Alsandi, Q., Tagami, J., & Zandinejad, A. (2023). Surface roughness and shear bond strength to composite resin of additively manufactured interim restorative material with different printing orientations. The Journal of Prosthetic Dentistry, 129(5), 788-795. https://doi.org/10.1016/j.prosdent.2021.08.010

Vancouver

Nasiry Khanlar L, Revilla-León M, Barmak AB, Ikeda M, Alsandi Q, Tagami J, et al. Surface roughness and shear bond strength to composite resin of additively manufactured interim restorative material with different printing orientations. The Journal of Prosthetic Dentistry. 2023;129(5):788-795. doi:10.1016/j.prosdent.2021.08.010

BibTeX
@article{NasiryKhanlar2023,
  author = {Nasiry Khanlar, Leila and Revilla-León, Marta and Barmak, Abdul Basir and Ikeda, Masaomi and Alsandi, Qutaiba and Tagami, Junji and Zandinejad, Amirali},
  title = {Surface roughness and shear bond strength to composite resin of additively manufactured interim restorative material with different printing orientations},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2023},
  volume = {129},
  number = {5},
  pages = {788--795},
  doi = {10.1016/j.prosdent.2021.08.010}
}
Kostenlos starten →