EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of resin cement type and autoclaving on the retention of zirconia on Ti‐base abutments

Carlos Eduardo Sabrosa iD, Karen Geber

Journal of Prosthodontics · 2026

DOI: 10.1111/jopr.70029 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2026. Verfasst von Carlos Eduardo Sabrosa und 1 weiteren Autor:innen. Beteiligte Einrichtung: University of the State of Rio de Janeiro Dental School, Rio de Janeiro, Brazil and IASERJ, Rio de Janeiro, Brazil. Hauptthemen laut MEDLINE: Zirconium, Resin Cements, Dental Abutments, Titanium. Die Arbeit nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The cement interface is particularly important for successful zirconia–titanium base (Ti‐base) restorations, as retention relies primarily on adhesive bonding. The aim of this in vitro study was to assess and compare the influence of a universal resin cement used with either a self‐adhesive or adhesive bonding protocol versus adhesive resin cements on the retention of zirconia to Ti‐base abutments, with and without autoclaving. Materials and Methods Zirconia buildups were cemented to titanium‐base abutments using RelyX Universal (RXU) as a self‐adhesive resin cement, RXU with a primer (RXU/SUP), Panavia V5 (PV5) with primer, or multilink hybrid abutment (MHA) with primer. Half of the specimens were autoclaved. Push‐out testing was performed, and data were statistically evaluated using the analysis of variance (ANOVA), Tukey honest significant difference test, and family‐wise error rate method.

Results

Of the nonautoclaved groups, RXU/SUP showed the highest initial mean push‐out load (1576.45 ± 195.86 N), followed by MHA (1268.10 ± 160.67 N), RXU (959.66 ± 139.24 N), and PV5 (905.84 ± 298.38 N). Autoclaving did not have a significant influence on cement push‐out load when compared directly within cement pairs. The push‐out load of RXU used as self‐adhesive cement was similar to PV5 with primer. Retention of RXU/SUP and MHA groups was significantly higher than that of RXU or PV5.

Conclusion

In this in vitro study, RXU performed as well as PV5 groups and required the fewest preparation steps, suggesting it may be a good option for improving workflow efficiency. Results indicated a marginally positive effect of autoclaving between pairs, however, it was not significant.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumResin CementsDental AbutmentsTitaniumDental Prosthesis RetentionDental MaterialsDental BondingMaterials TestingHumansIn Vitro TechniquesDental Stress AnalysisSurface Properties

Stichwörter der Autor:innen

adhesivesautoclavingimplant‐supported restorationresin cementsself‐adhesive resin cementzirconia retention

Substanzen

ZirconiumResin Cementszirconium oxideTitaniumDental Materials

Autor:innen und Institutionen

  • University of the State of Rio de Janeiro Dental School, Rio de Janeiro, Brazil and IASERJ, Rio de Janeiro, Brazil.
  • Private Practice, Rio de Janeiro, Brazil.

ORCID-Profile: Carlos Eduardo Sabrosa

Zitieren

APA

Sabrosa, C. E., & Geber, K. (2026). Effect of resin cement type and autoclaving on the retention of zirconia on Ti‐base abutments. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70029

Vancouver

Sabrosa CE, Geber K. Effect of resin cement type and autoclaving on the retention of zirconia on Ti‐base abutments. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70029

BibTeX
@article{Sabrosa2026,
  author = {Sabrosa, Carlos Eduardo and Geber, Karen},
  title = {Effect of resin cement type and autoclaving on the retention of zirconia on Ti‐base abutments},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70029}
}
Kostenlos starten →