EUVIMEDEUVIMED entdecken
Crossref

Clinical internal and marginal fit of metal‐ceramic fixed dental prostheses fabricated with selective laser melting and 3D‐printed pattern casting using cobalt‐chromium metal alloy

Saja Adel Bani-Younes, Rami S Al Fodeh iD, Lina Khasawneh, Abedelmalek Tabnjh

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13949 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Saja Adel Bani-Younes und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Jordan University of Science and Technology, Irbid, Jordan. Hauptthemen laut MEDLINE: Metal Ceramic Alloys, Chromium Alloys, Lasers, Dental Casting Technique. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 47 Literaturangaben. Gefördert von: Deanship of Scientific Research at Jordan University of Science and Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the fit of metal–ceramic three‐unit fixed dental prostheses (FDPs) fabricated using selective laser melting (SLM) and 3D‐printed casting pattern (CP) and to compare the effect of tooth type and ceramic veneering on marginal and internal gaps. Materials and Methods Patients requiring posterior three‐unit FDPs were selected. For each subject, two FDPs were fabricated using SLM and CP. Silicon replica was used to measure the internal and marginal fit of frameworks before and after ceramic veneering. For each replica, 36 measurements were performed using a stereomicroscope: 4 marginal and 32 internal (4 deep chamfers, 12 axial, 4 axio‐occlusal, and 12 occlusal). Statistical analysis was performed using two‐way ANOVA and paired t ‐test.

Results

A total of 44 metal–ceramic FDPs were fabricated in 22 patients. The results showed that the fabrication method had no significant effect on the marginal, deep chamfer, or occlusal gaps. However, the method significantly affected the axial, axio‐occlusal, and total internal fit, and the SLM had larger gaps than the CP. For the effect of ceramic veneering, measurements were significantly higher in the CP group at all gaps, except for the premolar axial and molar occlusal gaps. The SLM fit was less affected by ceramic veneering. Only premolar gaps significantly increased at the marginal, deep chamfer, and axial and axio‐occlusal positions.

Conclusion

Metal–ceramic FDPs fabricated using SLM and CP techniques provided a similar marginal fit. Premolars had smaller discrepancies compared to molars. The ceramic veneering process increased the gap of the prostheses, with SLM being less affected by ceramic veneering.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Metal Ceramic AlloysChromium AlloysLasersDental Casting TechniquePrinting, Three-DimensionalDental VeneersHumansDental Marginal AdaptationDenture, Partial, FixedFemaleDenture DesignMaleAdultMiddle Aged

Stichwörter der Autor:innen

SLMfitmetal‐ceramic FDPsreplica techniqueresin patterns

Substanzen

Metal Ceramic AlloysChromium Alloys

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Jordan University of Science and Technology, Irbid, Jordan.
  • Department of Applied Dental Sciences, Faculty of Applied Medical Sciences, Jordan University of Science and Technology, Irbid, Jordan.

ORCID-Profile: Rami S Al Fodeh

Förderung

  • Deanship of Scientific Research at Jordan University of Science and Technology

Zitieren

APA

Bani-Younes, S. A., Al Fodeh, R. S., Khasawneh, L., & Tabnjh, A. (2024). Clinical internal and marginal fit of metal‐ceramic fixed dental prostheses fabricated with selective laser melting and 3D‐printed pattern casting using cobalt‐chromium metal alloy. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13949

Vancouver

Bani-Younes SA, Al Fodeh RS, Khasawneh L, Tabnjh A. Clinical internal and marginal fit of metal‐ceramic fixed dental prostheses fabricated with selective laser melting and 3D‐printed pattern casting using cobalt‐chromium metal alloy. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13949

BibTeX
@article{BaniYounes2024,
  author = {Bani-Younes, Saja Adel and Al Fodeh, Rami S and Khasawneh, Lina and Tabnjh, Abedelmalek},
  title = {Clinical internal and marginal fit of metal‐ceramic fixed dental prostheses fabricated with selective laser melting and 3D‐printed pattern casting using cobalt‐chromium metal alloy},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13949}
}
Kostenlos starten →