EUVIMEDEUVIMED entdecken
Crossref

Zirconia specimens printed by vat photopolymerization: Mechanical properties, fatigue properties, and fractography analysis

Zidi Zhai, Chao Qian, Ting Jiao, Chun Xu, Jian Sun iD

Journal of Prosthodontics · 2026

DOI: 10.1111/jopr.13942 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2026. Verfasst von Zidi Zhai und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Shanghai Ninth People's Hospital, Shanghai Jiao Tong University School of Medicine, College of Stomatology, Shanghai Ji…. Hauptthemen laut MEDLINE: Zirconium, Dental Materials. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 38 Literaturangaben. Gefördert von: Stomatological Key Laboratory of Fujian College and University, School and Hospital of Stomatology, Fujian Medical University, Shanghai Committee of Science and Technology of China, Cross-disciplinary Research Fund of Shanghai Ninth People's Hospital, Shanghai JiaoTong University School of Medicine.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The mechanical and fatigue properties of zirconia specimens printed by vat photopolymerization (VPP) were evaluated and compared with those of zirconia specimens milled by computer numerical control (CNC). Materials and Methods Bar‐shaped specimens were printed by stereolithography (SL) and digital light processing (DLP). CNC‐milled specimens were used as control samples. The fracture toughness, hardness, and flexural strength properties of the zirconia specimens were evaluated via single edge V‐notch beam tests, Vickers hardness tests, and 3‐point bending tests. Dynamic fatigue tests were carried out in distilled water using a step‐stress test. After static bending and dynamic step‐stress testing, fractography analysis was performed. Statistical analysis was carried out to compare the fracture toughness, hardness, flexural strength, and fatigue cycle results of each group ( α = 0.05).

Results

The fracture toughness values did not significantly differ among the groups ( p > 0.05). The flexural strength was 894.10 MPa for SL, 831.46 MPa for DLP, and 1140.39 MPa for CNC. The flexural strength of CNC was greater than that of SL and DLP ( p < 0.01). The mean fatigue cycles were 23498.07 for SL, 19858.60 for DLP, and 31566.80 for CNC. The mean fatigue failure strength was 643.13 MPa for SL, 530.63 MPa for DLP, and 903.75 MPa for CNC. The fatigue failure strength of CNC was greater than that of SL and DLP ( p < 0.05). Fractography analysis revealed material defects at the fracture origin for each group. A partially fused structure of the incompletely debonded resin could be observed in SL, and a porous region of incompletely sintered zirconia grains could be observed in CNC.

Conclusions

The fracture toughness and hardness of zirconia printed by VPP are comparable to those of zirconia milled by CNC. However, zirconia milled by CNC has superior static flexural strength and dynamic fatigue resistance. Further studies are needed to explore the clinical applications of VPP‐printed zirconia.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumDental MaterialsPolymerizationMaterials TestingFlexural StrengthDental Stress AnalysisHardnessStress, Mechanical

Stichwörter der Autor:innen

3D printingfatigue propertyfractographymechanical propertyvat photopolymerizationzirconia

Substanzen

Zirconiumzirconium oxideDental Materials

Autor:innen und Institutionen

  • Department of Prosthodontics, Shanghai Ninth People's Hospital, Shanghai Jiao Tong University School of Medicine, College of Stomatology, Shanghai Jiao Tong University, National Center for Stomatology, National Clinical…

ORCID-Profile: Jian Sun

Förderung

  • Stomatological Key Laboratory of Fujian College and University, School and Hospital of Stomatology, Fujian Medical University
  • Shanghai Committee of Science and Technology of China
  • Cross-disciplinary Research Fund of Shanghai Ninth People's Hospital, Shanghai JiaoTong University School of Medicine

Zitieren

APA

Zhai, Z., Qian, C., Jiao, T., Xu, C., & Sun, J. (2026). Zirconia specimens printed by vat photopolymerization: Mechanical properties, fatigue properties, and fractography analysis. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13942

Vancouver

Zhai Z, Qian C, Jiao T, Xu C, Sun J. Zirconia specimens printed by vat photopolymerization: Mechanical properties, fatigue properties, and fractography analysis. Journal of Prosthodontics. 2026. doi:10.1111/jopr.13942

BibTeX
@article{Zhai2026,
  author = {Zhai, Zidi and Qian, Chao and Jiao, Ting and Xu, Chun and Sun, Jian},
  title = {Zirconia specimens printed by vat photopolymerization: Mechanical properties, fatigue properties, and fractography analysis},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.13942}
}
Kostenlos starten →