EUVIMEDEUVIMED entdecken
Crossref

Effectiveness of different surface treatments on bond strength between 3D‐printed teeth and denture base

Anne Karoline de Holanda Cavalcanti Pereira iD, Rayanna Thayse Florêncio Costa, Rafaella de Souza Leão, Bruno Gustavo da Silva Casado, Andre Ulisses Dantas Batista, Sandra Lúcia Dantas Moraes iD

Journal of Prosthodontics · 2026-10 · 35 (8) · 1281-1289

DOI: 10.1111/jopr.13941 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 21.09.2024. Verfasst von Anne Karoline de Holanda Cavalcanti Pereira und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral Rehabilitation, Faculty of Dentistry, University of Pernambuco (FOP/UPE), Recife, Brazil. Hauptthemen laut MEDLINE: Denture Bases, Dental Bonding, Printing, Three-Dimensional, Tooth, Artificial. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 43 Literaturangaben. Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To investigate the effects of different surface treatments and thermal cycling on the shear bond strength between 3D‐printed teeth and denture bases. Materials and Methods For the shear bond strength (SBS) test, the specimens were the maxillary central incisors (11 × 9 × 7 mm) bonded on a cylindrical base (20 × 25 mm). The control group was heat‐cured polymethylmethacrylate (PMMA) ( N = 20). The printed group was divided into five subgroups ( N = 20): no treatment, sandblasting with aluminum oxide (Al 2 O 3 ), methyl methacrylate monomer, acetone, and adhesive with urethane dimethacrylate. Half of the samples were subjected to 2000 thermal cycling cycles, and all samples were subjected to the SBS test. The failure mode was established as adhesive, cohesive, or mixed through stereomicroscopic analysis. The surface roughness test (Sa) was performed using optical profilometry, and the rectangular specimens (14 × 14 × 2.5 mm) were divided into four groups according to the surface treatments ( N = 7 per group). Paired T and Wilcoxon tests were conducted to perform comparisons within the same group. The Kruskal–Wallis and Dwass‐Steel‐Critchlow‐Fligner post‐hoc tests were conducted to compare the groups.

Results

Al 2 O 3 sandblasting in the 3D‐printed groups achieved high SBS values comparable to those of the control group in the thermal cycled ( p = 0.962) and non‐thermal cycled samples ( p = 0.319). It was the only treatment capable of modifying the surface of the 3D‐printed resin, thereby increasing the roughness ( p = 0.016).

Conclusions

Sandblasting is recommended to increase the bond strength between the tooth and denture bases.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesDental BondingPrinting, Three-DimensionalTooth, ArtificialSurface PropertiesShear StrengthHumansPolymethyl MethacrylateDental Stress AnalysisMaterials TestingAluminum Oxide

Stichwörter der Autor:innen

3D printingCAD‐CAMartificial toothbond strengthdenture basedigital denturesurface treatment

Substanzen

Polymethyl MethacrylateAluminum Oxide

Autor:innen und Institutionen

  • Department of Oral Rehabilitation, Faculty of Dentistry, University of Pernambuco (FOP/UPE), Recife, Brazil.
  • Department of Dentistry, Federal University of Paraíba (UFPB), João Pessoa, Paraíba, Brazil.

ORCID-Profile: Anne Karoline de Holanda Cavalcanti Pereira, Sandra Lúcia Dantas Moraes

Förderung

  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Zitieren

APA

Pereira, A. K. H. C., Costa, R. T. F., Leão, R. S., Casado, B. G. D. S., Batista, A. U. D., & Moraes, S. L. D. (2026). Effectiveness of different surface treatments on bond strength between 3D‐printed teeth and denture base. Journal of Prosthodontics, 35(8), 1281-1289. https://doi.org/10.1111/jopr.13941

Vancouver

Pereira AKHC, Costa RTF, Leão RS, Casado BGDS, Batista AUD, Moraes SLD. Effectiveness of different surface treatments on bond strength between 3D‐printed teeth and denture base. Journal of Prosthodontics. 2026;35(8):1281-1289. doi:10.1111/jopr.13941

BibTeX
@article{Pereira2026,
  author = {Pereira, Anne Karoline de Holanda Cavalcanti and Costa, Rayanna Thayse Florêncio and Leão, Rafaella de Souza and Casado, Bruno Gustavo da Silva and Batista, Andre Ulisses Dantas and Moraes, Sandra Lúcia Dantas},
  title = {Effectiveness of different surface treatments on bond strength between 3D‐printed teeth and denture base},
  journal = {Journal of Prosthodontics},
  year = {2026},
  volume = {35},
  number = {8},
  pages = {1281--1289},
  doi = {10.1111/jopr.13941}
}
Kostenlos starten →