EUVIMEDEUVIMED entdecken
Crossref

Physical, Mechanical, and Anti‐Biofilm Formation Properties of CAD‐CAM Milled or 3D Printed Denture Base Resins: In Vitro Analysis

Rodrigo Falcão Carvalho Porto de Freitas iD, Simone Duarte, Sabrina Feitosa iD, Vinicius Dutra iD, Wei-Shao Lin iD, Beatriz Helena Dias Panariello iD, Adriana da Fonte Porto Carreiro iD

Journal of Prosthodontics · 2023-04 · 32 (S1) · 38-44

DOI: 10.1111/jopr.13554 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 09.07.2022. Verfasst von Rodrigo Falcão Carvalho Porto de Freitas und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dentistry, Federal University of Rio Grande do Norte, Natal, Brazil. Hauptthemen laut MEDLINE: Polymethyl Methacrylate, Denture Bases. Die Arbeit wurde bisher 88-mal zitiert (Crossref) und nennt 36 Literaturangaben. Gefördert von: Conselho Nacional de Desenvolvimento Científico e Tecnológico, National Council for Scientific and Technological Development (CNPq).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To investigate surface characteristics (roughness and contact angle), anti‐biofilm formation, and mechanical properties (mini‐flexural strength) of computer‐aided design and computer‐aided manufacturing (CAD‐CAM) polymethylmethacrylate (PMMA) polymer, and three‐dimensional (3D) printed resin for denture base fabrication compared with conventional heat polymerized denture base resins. Materials and methods A total of 60 discs and 40 rectangular specimens were fabricated from one CAD‐CAM (AvaDent), one 3D printed (Cosmos Denture), and two conventional heat polymerized (Lucitone 199 and VipiWave) materials for denture base fabrication. Roughness was determined by Ra value; the contact angle was measured by the sessile drop method. The biofilm formation inhibition behavior was analyzed through Candida albicans adhesion, while mini‐flexural strength test was done using a three‐point bending test. The data were analyzed using descriptive and analytical statistics (α = 0.05).

Results

The CAD‐CAM PMMA group showed the lowest C. albicans adhesion (log CFU/mL: 3.74 ± 0.57) and highest mini‐flexural strength mean (114.96 ± 16.23 MPa). 3D printed specimens presented the highest surface roughness (Ra: 0.317 ± 0.151 μm) and lowest mini‐flexural strength values (57.23 ± 9.07 MPa). However, there was no statistical difference between CAD‐CAM PMMA and conventional groups for roughness, contact angle, and mini‐flexural strength.

Conclusions

CAD‐CAM milled materials present surface and mechanical properties similar to conventional resins and show improved behavior in preventing C. albicans adhesion. Nevertheless, 3D printed resins present decreased mini‐flexural strength.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Polymethyl MethacrylateDenture BasesMaterials TestingSurface PropertiesComputer-Aided DesignPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D printingadditive manufacturingcomplete denturescomputer-aided designcomputer-aided manufacturingdigital denturesphotocurable resinsubtractive manufacturing

Substanzen

Polymethyl Methacrylate

Autor:innen und Institutionen

  • Department of Dentistry, Federal University of Rio Grande do Norte, Natal, Brazil.
  • Department of Cariology, Operative Dentistry and Dental Public Health, Indiana University School of Dentistry, Indianapolis, IN.
  • Department of Biomedical Sciences and Comprehensive Care, Division of Biomedical and Applied Sciences, Indiana University School of Dentistry, Indianapolis, IN.
  • Department of Oral Pathology, Medicine and Radiology, Indiana University School of Dentistry, Indianapolis, IN.
  • Department of Prosthodontics, Indiana University School of Dentistry, Indianapolis, IN.

ORCID-Profile: Rodrigo Falcão Carvalho Porto de Freitas, Sabrina Feitosa, Vinicius Dutra, Wei-Shao Lin, Beatriz Helena Dias Panariello, Adriana da Fonte Porto Carreiro

Förderung

  • Conselho Nacional de Desenvolvimento Científico e Tecnológico
  • National Council for Scientific and Technological Development (CNPq)

Zitieren

APA

Freitas, R. F. C. P., Duarte, S., Feitosa, S., Dutra, V., Lin, W. S., Panariello, B. H. D., & Carreiro, A. D. F. P. (2023). Physical, Mechanical, and Anti‐Biofilm Formation Properties of CAD‐CAM Milled or 3D Printed Denture Base Resins: In Vitro Analysis. Journal of Prosthodontics, 32(S1), 38-44. https://doi.org/10.1111/jopr.13554

Vancouver

Freitas RFCP, Duarte S, Feitosa S, Dutra V, Lin WS, Panariello BHD, et al. Physical, Mechanical, and Anti‐Biofilm Formation Properties of CAD‐CAM Milled or 3D Printed Denture Base Resins: In Vitro Analysis. Journal of Prosthodontics. 2023;32(S1):38-44. doi:10.1111/jopr.13554

BibTeX
@article{Freitas2023,
  author = {Freitas, Rodrigo Falcão Carvalho Porto de and Duarte, Simone and Feitosa, Sabrina and Dutra, Vinicius and Lin, Wei-Shao and Panariello, Beatriz Helena Dias and Carreiro, Adriana da Fonte Porto},
  title = {Physical, Mechanical, and Anti‐Biofilm Formation Properties of CAD‐CAM Milled or 3D Printed Denture Base Resins: In Vitro Analysis},
  journal = {Journal of Prosthodontics},
  year = {2023},
  volume = {32},
  number = {S1},
  pages = {38--44},
  doi = {10.1111/jopr.13554}
}
Kostenlos starten →