Targeting bonding protocols to increase the bond between acrylic resin or 3D printed denture bases and prefabricated or 3D printed denture teeth
The Journal of Prosthetic Dentistry · 2024-06 · 131 (6) · 1252.e1-1252.e10
DOI: 10.1016/j.prosdent.2024.02.027 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024-06. Verfasst von Ana Larisse Carneiro Pereira und 6 weiteren Autor:innen. Beteiligte Einrichtung: PhD Candidate, Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Acrylic Resins, Denture Bases, Tooth, Artificial. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 46 Literaturangaben. Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: The difference in chemical composition between denture base resin and denture teeth requires the development of bonding protocols that increase the union between the materials. PURPOSE: The purpose of this in vitro study was to evaluate the impact of different bonding protocols on the bond between heat-polymerized and 3-dimensionally (3D) printed acrylic resin denture bases and acrylic resin prefabricated and 3D printed artificial teeth. MATERIAL AND METHODS: Four types of artificial teeth were evaluated: prefabricated acrylic resin (VITA MFT) and 3D printed (Cosmos TEMP, PRIZMA 3D Bio Denture, and PrintaX AA Temp) bonded to 20×24-mm cylinders of heat-polymerized (VipiWave) and 3D printed (Cosmos Denture, PRIZMA 3D Bio Denture, and PrintaX BB Base) denture bases. Three bonding protocols were tested (n=20): mechanical retention with perforation + monomer (PT1), mechanical retention with perforation + airborne-particle abrasion with 50-µm aluminum oxide + monomer (PT2), and mechanical retention with perforation + Palabond (PT3). Half of the specimens in each group received 10 000 thermocycles and were then subjected to the bonding test at a crosshead speed of 1 mm/minute. The failure type was analyzed and scanning electron micrographs made. Additionally, surface roughness (Ra) and wettability (degree) were analyzed (n=15). ANOVA was used to evaluate the effect of the bonding protocol, and the Student t test was applied to compare the experimental groups with the control (α=.05). For type of failure, a descriptive analysis was carried out using absolute and relative frequency. The Kruskal-Wallis test was used to evaluate the surface changes (α=.05). RESULTS: Among the protocols, PT3 with in Yller and PT2 with Prizma had the highest bond strengths of the heat-polymerized denture base and 3D printed teeth (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- PhD Candidate, Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Brazil.
- Researcher, Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Brazil.
- Researcher, Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), São Paulo, Brazil.
- Professor, Department of Biomaterials, Dental Materials, and Prosthodontics, Institute of Science and Technology, São Paulo State University (UNESP), São José dos Campos, Brazil.
- Associate Professor, Department of Prosthodontics and Periodontology, Piracicaba Dental School, State University of Campinas (UNICAMP), Piracicaba, Brazil.
- Full Professor, Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Brazil. Electronic address: adriana.carreiro@ufrn.br.
Förderung
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Zitieren
APA
Pereira, A. L. C., Porto de Freitas, R. F. C., Grangeiro, M. T. V., de Medeiros, A. K. B., Bottino, M. A., Barão, V. A. R., & Carreiro, A. D. F. P. (2024). Targeting bonding protocols to increase the bond between acrylic resin or 3D printed denture bases and prefabricated or 3D printed denture teeth. The Journal of Prosthetic Dentistry, 131(6), 1252.e1-1252.e10. https://doi.org/10.1016/j.prosdent.2024.02.027
Vancouver
Pereira ALC, Porto de Freitas RFC, Grangeiro MTV, de Medeiros AKB, Bottino MA, Barão VAR, et al. Targeting bonding protocols to increase the bond between acrylic resin or 3D printed denture bases and prefabricated or 3D printed denture teeth. The Journal of Prosthetic Dentistry. 2024;131(6):1252.e1-1252.e10. doi:10.1016/j.prosdent.2024.02.027
BibTeX
@article{Pereira2024,
author = {Pereira, Ana Larisse Carneiro and Porto de Freitas, Rodrigo Falcão Carvalho and Grangeiro, Manassés Tercio Vieira and de Medeiros, Annie Karoline Bezerra and Bottino, Marco Antônio and Barão, Valentim A R and Carreiro, Adriana da Fonte Porto},
title = {Targeting bonding protocols to increase the bond between acrylic resin or 3D printed denture bases and prefabricated or 3D printed denture teeth},
journal = {The Journal of Prosthetic Dentistry},
year = {2024},
volume = {131},
number = {6},
pages = {1252.e1--1252.e10},
doi = {10.1016/j.prosdent.2024.02.027}
}
EUVIMED