EUVIMEDObjevte EUVIMED
Open access · CC BY-NC-ND 4.0

Assessment of Monomer Release From Resin Composites Following the Use of Various Modeling Liquids

Dorukcan Yıldırım iD, Hüseyin Hatırlı, Emine Şirin Karaarslan, Tarık Balkan iD

Journal of Esthetic and Restorative Dentistry · 2026

DOI: 10.1111/jerd.70195 ↗

At a glance

Journal article in Journal of Esthetic and Restorative Dentistry, 2026. Written by Dorukcan Yıldırım and 3 co-authors. Institution: Department of Restorative Dentistry, Faculty of Dentistry, Yozgat Bozok University, Yozgat, Turkey. Major MEDLINE topics: Composite Resins. Cited 1 times so far (Crossref); 40 references. The full text is freely available (open access, CC BY-NC-ND 4.0).

AbstraktSubjectsBibliografické údajeCiteRelated studies

Abstract (original language)

Objectives

The chemical composition of resin composites and the use of modeling liquids may influence the release of residual monomer, potentially impacting biocompatibility. This in vitro study evaluated the effect of different modeling liquids on the elution of monomers from two resin composites. Materials and Methods Eighty disc‐shaped samples were prepared using two nano‐hybrid resin composites (Estelite Sigma Quick, Tokuyama; Harmonize, KERR) and three modeling liquids; Composite Wetting Resin (Ultradent, USA), Modeling Resin (Bisco, USA), and Modeling Liquid (GC, Japan) ( n = 10). Resin composites were placed in four 0.5‐mm increments into Teflon molds, and modeling liquids were applied with a brush between layers; control groups were prepared without modeling liquids. After polishing (Sof‐Lex, 3 M ESPE), specimens were stored in 75% ethanol at 37°C. Release of UDMA, Bis‐GMA, TEGDMA, and HEMA was quantified using a liquid chromatography–tandem mass spectrometry (LC–MS/MS) system (LCMS‐8050, Shimadzu, Japan) at 24 h, 7 days, and 30 days. Data normality was assessed, and effects of resin composites type, modeling liquid, and time were analyzed using three‐way ANOVA with Bonferroni post hoc testing (α = 0.05).

Results

Application of modeling liquid significantly reduced Bis‐GMA release for both resin composites ( p < 0.05). While TEGDMA release was significantly decreased in Estelite Sigma Quick groups ( p < 0.05), no difference was observed in Harmonize groups. Modeling liquid applications increased total HEMA and UDMA release ( p < 0.05). TEGDMA release in the Estelite Sigma Quick‐control group was higher than the Harmonize‐control group ( p < 0.05).

Conclusion

The organic matrix of composite resins and the modeling liquids used influence the release of the tested monomers (TEGDMA, BisGMA, UDMA, and HEMA). The use of modeling liquid showed differences in monomer release according to the content of the liquid. Clinical Significance Modeling liquids may increase residual monomer release from resin composites, particularly shortly after polymerization. Clinicians should use these materials sparingly and in accordance with manufacturers' instructions to minimize potential biocompatibility risks.

Subjects

MeSH terms (MEDLINE)

Composite ResinsMaterials TestingMethacrylatesPolyethylene GlycolsIn Vitro TechniquesBisphenol A-Glycidyl MethacrylatePolymethacrylic Acids

Author keywords

LC–MS/MSmodeling liquidmonomer elutionresidual monomerresin composites

Substances

Composite ResinsMethacrylatestriethylene glycol dimethacrylatePolyethylene GlycolsBisphenol A-Glycidyl MethacrylatePolymethacrylic Acids

Authors and institutions

  • Department of Restorative Dentistry, Faculty of Dentistry, Yozgat Bozok University, Yozgat, Turkey.
  • Department of Restorative Dentistry, Faculty of Dentistry, Tokat Gaziosmanpasa University, Tokat, Turkey.
  • Department of Plant Protection, Faculty of Agriculture, Tokat Gaziosmanpaşa University, Tokat, Turkey.

ORCID profiles: Dorukcan Yıldırım, Tarık Balkan

Cite

APA

Yıldırım, D., Hatırlı, H., Karaarslan, E. Ş., & Balkan, T. (2026). Assessment of Monomer Release From Resin Composites Following the Use of Various Modeling Liquids. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.70195

Vancouver

Yıldırım D, Hatırlı H, Karaarslan EŞ, Balkan T. Assessment of Monomer Release From Resin Composites Following the Use of Various Modeling Liquids. Journal of Esthetic and Restorative Dentistry. 2026. doi:10.1111/jerd.70195

BibTeX
@article{Yldrm2026,
  author = {Yıldırım, Dorukcan and Hatırlı, Hüseyin and Karaarslan, Emine Şirin and Balkan, Tarık},
  title = {Assessment of Monomer Release From Resin Composites Following the Use of Various Modeling Liquids},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2026},
  doi = {10.1111/jerd.70195}
}
Start for free →