EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

A Review of Current Systems, Materials, and Protocols for 3D ‐Printed Splints, Crowns, and Dentures

Pouya Sabanik, Ting-Chia Liu, Mahmoudreza Tabatabaeian, Mateus G Rocha, Neeraj Surathu iD, Nathaniel C Lawson

Journal of Esthetic and Restorative Dentistry · 2026-03 · 38 (3) · 635-651

DOI: 10.1111/jerd.70125 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Journal of Esthetic and Restorative Dentistry, online erschienen am 17.02.2026. Verfasst von Pouya Sabanik und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Clinical and Community Sciences, The University of Alabama at Birmingham School of Dentistry, Birmingham, Alabama, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Crowns, Dental Materials, Splints. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 171 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To summarize and synthesize evidence‐based conclusions on optimal three‐dimensional (3D) printing technologies, materials, and clinical protocols for splints, crowns, and dentures. Overview In resin vat printing, stereolithography (SLA) offers superior surface finish, while liquid crystal display (LCD) and digital light processing (DLP) excel in speed for larger prints, with LCD providing a cost advantage. Ceramic vat printing yields clinically acceptable strength but is equipment‐ and time‐intensive. Optimal angulation varies by application: splints (0°), crowns (150°–210°), dentures (45°–90°). A 50 μm layer height is preferred for most restorations, with dentures tolerating 100 μm. Commonly used resins employ low‐viscosity monomers (e.g., ethoxylated bisphenol A dimethacrylate [Bis‐EMA]) that limit stiffness and fast photoinitiators (e.g., ethyl (2,4,6‐trimethylbenzoyl) phenylphosphinate [TPO]), requiring 385–405 nm curing.

Conclusions

Flexible splints excel in fracture toughness and impact strength; firm splints match milled wear performance. Printed crowns, while weaker than milled options, offer toughness; wear rates remain a concern. Printed denture bases vary in strength but can match or exceed conventional options; printed teeth show favorable wear resistance. Postprocessing, polishing, and bonding protocols critically influence outcomes. Clinical Significance Employing validated printing parameters, selecting the appropriate resin, and following evidence‐based protocols allows clinicians to maximize restoration accuracy and mechanical performance while leveraging 3D printing's efficiency and cost benefits.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalCrownsDental MaterialsSplintsDenturesHumans

Stichwörter der Autor:innen

3D printingSLAbonding protocolsdental crownsfiller contentocclusal splintspostcuringprinted denturesvat polymerizationzirconia

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Department of Clinical and Community Sciences, The University of Alabama at Birmingham School of Dentistry, Birmingham, Alabama, USA.
  • Department of Restorative Dental Sciences, University of Florida School of Dentistry, Gainesville, Florida, USA.
  • The ACE Institute, Hamilton, New Zealand.

ORCID-Profile: Neeraj Surathu

Zitieren

APA

Sabanik, P., Liu, T. C., Tabatabaeian, M., Rocha, M. G., Surathu, N., & Lawson, N. C. (2026). A Review of Current Systems, Materials, and Protocols for 3D ‐Printed Splints, Crowns, and Dentures. Journal of Esthetic and Restorative Dentistry, 38(3), 635-651. https://doi.org/10.1111/jerd.70125

Vancouver

Sabanik P, Liu TC, Tabatabaeian M, Rocha MG, Surathu N, Lawson NC. A Review of Current Systems, Materials, and Protocols for 3D ‐Printed Splints, Crowns, and Dentures. Journal of Esthetic and Restorative Dentistry. 2026;38(3):635-651. doi:10.1111/jerd.70125

BibTeX
@article{Sabanik2026,
  author = {Sabanik, Pouya and Liu, Ting-Chia and Tabatabaeian, Mahmoudreza and Rocha, Mateus G and Surathu, Neeraj and Lawson, Nathaniel C},
  title = {A Review of Current Systems, Materials, and Protocols for 3D ‐Printed Splints, Crowns, and Dentures},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2026},
  volume = {38},
  number = {3},
  pages = {635--651},
  doi = {10.1111/jerd.70125}
}
Kostenlos starten →