In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units
Journal of Esthetic and Restorative Dentistry · 2023
DOI: 10.1111/jerd.13022 ↗At a glance
Journal article in Journal of Esthetic and Restorative Dentistry, 2023. Written by Cristiane Maucoski and 5 co-authors. Institution: Department of Restorative Dentistry, State University of Ponta Grossa, Ponta Grossa, Parana, Brazil. Major MEDLINE topics: Curing Lights, Dental, Dental Caries. Cited 20 times so far (Crossref); 51 references. The full text is freely available (open access, CC BY-NC-ND 4.0). Funded by: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Dalhousie University, Mitacs.
Abstract (original language)
Objective
To evaluate the in vitro pulpal temperature rise (Δ T ) within the pulp chamber when low‐ and high‐viscosity bulk‐fill resin composites are photo‐cured using laser or contemporary light curing units (LCUs). Materials and Methods The light output from five LCUs was measured. Non‐retentive Class I and V cavities were prepared in one upper molar. Two T‐type thermocouples were inserted into the pulp chamber. After the PT values reached 32°C under simulated pulp flow (0.026 mL/min), both cavities were restored with: Filtek One Bulk Fill (3 M), Filtek Bulk Fill Flow (3 M), Tetric PowerFill (Ivoclar Vivadent), or Tetric PowerFlow (Ivoclar Vivadent). The tooth was exposed as follows: Monet Laser (1 and 3 s), PowerCure (3 and 20 s), PinkWave (3 and 20 s), Valo X (5 and 20 s) and SmartLite Pro (20 s). The Δ T data were subjected to one‐way ANOVA followed by Scheffe's post hoc test.
Results
Monet 1 s (1.9 J) and PinkWave 20 s (30.1 J) delivered the least and the highest amount of energy, respectively. Valo X and PinkWave used for 20 s produced the highest Δ T values (3.4–4.1°C). Monet 1 s, PinkWave 3 s, PowerCure 3 s (except FB‐Flow) and Monet 3 s for FB‐One and TP‐Fill produced the lowest Δ T values (0.9–1.7°C). No significant differences were found among composites.
Conclusions
Short 1‐ to 3‐s exposures produced acceptable temperature rises, regardless of the composite. Clinical Significance The energy delivered to the tooth by the LCUs affects the temperature rise inside the pulp. The short 1–3 s exposure times used in this study delivered the least amount of energy and produced a lower temperature rise. However, the RBC may not have received sufficient energy to be adequately photo‐cured.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- Department of Restorative Dentistry, State University of Ponta Grossa, Ponta Grossa, Parana, Brazil.
- Department of Dental Clinical Sciences, Faculty of Dentistry, Dalhousie University, Halifax, Nova Scotia, Canada.
ORCID profiles: Cristiane Maucoski, Richard Bengt Price, Braden Sullivan, Juliana Anany Gonzales Guarneri, Bruno Gusso, Cesar Augusto Galvão Arrais
Funding
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
- Dalhousie University
- Mitacs
Cite
APA
Maucoski, C., Price, R. B., Sullivan, B., Guarneri, J. A. G., Gusso, B., & Arrais, C. A. G. (2023). In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13022
Vancouver
Maucoski C, Price RB, Sullivan B, Guarneri JAG, Gusso B, Arrais CAG. In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units. Journal of Esthetic and Restorative Dentistry. 2023. doi:10.1111/jerd.13022
BibTeX
@article{Maucoski2023,
author = {Maucoski, Cristiane and Price, Richard Bengt and Sullivan, Braden and Guarneri, Juliana Anany Gonzales and Gusso, Bruno and Arrais, Cesar Augusto Galvão},
title = {In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units},
journal = {Journal of Esthetic and Restorative Dentistry},
year = {2023},
doi = {10.1111/jerd.13022}
}
EUVIMED