EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units

Cristiane Maucoski iD, Richard Bengt Price iD, Braden Sullivan iD, Juliana Anany Gonzales Guarneri iD, Bruno Gusso iD, Cesar Augusto Galvão Arrais iD

Journal of Esthetic and Restorative Dentistry · 2023

DOI: 10.1111/jerd.13022 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, 2023. Verfasst von Cristiane Maucoski und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, State University of Ponta Grossa, Ponta Grossa, Parana, Brazil. Hauptthemen laut MEDLINE: Curing Lights, Dental, Dental Caries. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Dalhousie University, Mitacs.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To evaluate the in vitro pulpal temperature rise (Δ T ) within the pulp chamber when low‐ and high‐viscosity bulk‐fill resin composites are photo‐cured using laser or contemporary light curing units (LCUs). Materials and Methods The light output from five LCUs was measured. Non‐retentive Class I and V cavities were prepared in one upper molar. Two T‐type thermocouples were inserted into the pulp chamber. After the PT values reached 32°C under simulated pulp flow (0.026 mL/min), both cavities were restored with: Filtek One Bulk Fill (3 M), Filtek Bulk Fill Flow (3 M), Tetric PowerFill (Ivoclar Vivadent), or Tetric PowerFlow (Ivoclar Vivadent). The tooth was exposed as follows: Monet Laser (1 and 3 s), PowerCure (3 and 20 s), PinkWave (3 and 20 s), Valo X (5 and 20 s) and SmartLite Pro (20 s). The Δ T data were subjected to one‐way ANOVA followed by Scheffe's post hoc test.

Results

Monet 1 s (1.9 J) and PinkWave 20 s (30.1 J) delivered the least and the highest amount of energy, respectively. Valo X and PinkWave used for 20 s produced the highest Δ T values (3.4–4.1°C). Monet 1 s, PinkWave 3 s, PowerCure 3 s (except FB‐Flow) and Monet 3 s for FB‐One and TP‐Fill produced the lowest Δ T values (0.9–1.7°C). No significant differences were found among composites.

Conclusions

Short 1‐ to 3‐s exposures produced acceptable temperature rises, regardless of the composite. Clinical Significance The energy delivered to the tooth by the LCUs affects the temperature rise inside the pulp. The short 1–3 s exposure times used in this study delivered the least amount of energy and produced a lower temperature rise. However, the RBC may not have received sufficient energy to be adequately photo‐cured.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Curing Lights, DentalDental CariesHumansTemperatureLight-Curing of Dental AdhesivesComposite ResinsDental MaterialsMaterials TestingPolymerizationAcrylic ResinsPolyurethanes

Stichwörter der Autor:innen

dental curing lightsdental pulplaserresin-based compositetemperature

Substanzen

Composite ResinsDental MaterialsVivadentAcrylic ResinsPolyurethanes

Autor:innen und Institutionen

  • Department of Restorative Dentistry, State University of Ponta Grossa, Ponta Grossa, Parana, Brazil.
  • Department of Dental Clinical Sciences, Faculty of Dentistry, Dalhousie University, Halifax, Nova Scotia, Canada.

ORCID-Profile: Cristiane Maucoski, Richard Bengt Price, Braden Sullivan, Juliana Anany Gonzales Guarneri, Bruno Gusso, Cesar Augusto Galvão Arrais

Förderung

  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
  • Dalhousie University
  • Mitacs

Zitieren

APA

Maucoski, C., Price, R. B., Sullivan, B., Guarneri, J. A. G., Gusso, B., & Arrais, C. A. G. (2023). In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13022

Vancouver

Maucoski C, Price RB, Sullivan B, Guarneri JAG, Gusso B, Arrais CAG. In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units. Journal of Esthetic and Restorative Dentistry. 2023. doi:10.1111/jerd.13022

BibTeX
@article{Maucoski2023,
  author = {Maucoski, Cristiane and Price, Richard Bengt and Sullivan, Braden and Guarneri, Juliana Anany Gonzales and Gusso, Bruno and Arrais, Cesar Augusto Galvão},
  title = {In‐vitro pulpal temperature increases when photo‐curing bulk‐fill resin‐based composites using laser or light‐emitting diode light curing units},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2023},
  doi = {10.1111/jerd.13022}
}
Kostenlos starten →