Fracture load and three‐dimensional internal void analysis of direct composites used to restore worn molars
European Journal of Oral Sciences · 2026
DOI: 10.1111/eos.70104 ↗At a glance
Vergleichsstudie in European Journal of Oral Sciences, 2026. Written by Topias Yli-Urpo and 6 co-authors. Institution: Institute of Dentistry, University of Turku, Turku, Finland. Major MEDLINE topics: Composite Resins, Molar, Tooth Wear, Dental Materials. 48 references. The full text is freely available (open access, CC BY 4.0). Funded by: University of Turku, Turun Yliopisto.
Abstract (original language)
This study evaluated (1) the load‐bearing capacity of molars restored with direct occlusal veneers fabricated either from short‐fiber‐reinforced composite (SFRC) or particulate‐filled composite (PFC) and the presence of internal voids within the materials, and (2) effect of water storage on the fracture load and correlation between internal voids and fracture load. Sixty human molars ( n = 10/group) were prepared with flat occlusal surfaces and preserved enamel margins simulating worn teeth. Conventional molds were taken for each tooth to control the preparation depth and transparent molds to restore the teeth to their original shape. Following bonding procedure, teeth were restored with flowable SFRC, flowable PFC, or condensable PFC using either injectable or pressing technique. Restored teeth were stored in water for 1 d or 6 months before the static loading test. Fracture mode and three‐dimensional internal void analyses were additionally conducted. SFRC occlusal veneers showed significantly higher fracture load (3661 ± 446 N) than both PFC materials, flowable PFC (2064 ± 372 N) and condensable PFC (2183 ± 563 N). SFRC redirected the fractures towards the periphery of the restoration. Prolonged water storage duration or single voids did not adversely affect the fracture load. The use of SFRC as occlusal veneers for restoring molars improves the fracture load and the fracture propagation.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- Institute of Dentistry, University of Turku, Turku, Finland.
- Institute of Biomedicine, Faculty of Medicine, University of Turku, Turku, Finland.
- Department of Community Dentistry, Institute of Dentistry, University of Turku, Turku, Finland.
- Department of Biomaterials Science and Turku Clinical Biomaterials Centre, Institute of Dentistry, University of Turku, Turku, Finland.
- Oral Health Services, Wellbeing Services County of Southwest Finland, Turku, Finland.
- Department of Prosthetic Dentistry and Stomatognathic Physiology, Institute of Dentistry, University of Turku, Turku, Finland.
Funding
- University of Turku
- Turun Yliopisto
Cite
APA
Yli-Urpo, T., Määttä, J., Suominen, A., Vallittu, P. K., Närhi, T., Le Bell-Rönnlöf, A. M., & Bijelic-Donova, J. (2026). Fracture load and three‐dimensional internal void analysis of direct composites used to restore worn molars. European Journal of Oral Sciences. https://doi.org/10.1111/eos.70104
Vancouver
Yli-Urpo T, Määttä J, Suominen A, Vallittu PK, Närhi T, Le Bell-Rönnlöf AM, et al. Fracture load and three‐dimensional internal void analysis of direct composites used to restore worn molars. European Journal of Oral Sciences. 2026. doi:10.1111/eos.70104
BibTeX
@article{YliUrpo2026,
author = {Yli-Urpo, Topias and Määttä, Jorma and Suominen, Auli and Vallittu, Pekka K and Närhi, Timo and Le Bell-Rönnlöf, Anna-Maria and Bijelic-Donova, Jasmina},
title = {Fracture load and three‐dimensional internal void analysis of direct composites used to restore worn molars},
journal = {European Journal of Oral Sciences},
year = {2026},
doi = {10.1111/eos.70104}
}
EUVIMED