EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of printing orientation and post‐curing on optical and surface properties of definitive three‐dimensional‐printed dental resin with inorganic fillers

Luana Dos Santos Souza iD, Andrea Mendoza iD, Taciana Marco Ferraz Caneppele iD, Pablo Lenin Benitez Sellan iD, Eduardo Bresciani iD

European Journal of Oral Sciences · 2026-08 · 134 (4)

DOI: 10.1111/eos.70083 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Oral Sciences, online erschienen am 09.03.2026. Verfasst von Luana Dos Santos Souza und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Institute of Science and Technology, São Paulo State University (UNESP), São José dos Campos, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Composite Resins, Dental Materials. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the influence of printing orientation and post‐curing on the color stability, gloss retention, and surface microhardness of a definitive three‐dimensional (3D)‐printed dental resin, a high‐strength photopolymer with inorganic fillers designed for permanent restorations, after immersion in a staining solution. Circular specimens (6 mm diameter and 1.5 mm thickness) were printed at 0°, 45°, and 90° orientations and divided into two groups: control ( n = 10), post‐cured according to the manufacturer's protocol, and negative control ( n = 10), without post‐curing. Baseline color ( L * , a * , b * ), gloss, and Knoop microhardness were measured, followed by reassessment after 21 days of immersion in a staining solution. Data were analyzed using two‐way and repeated‐measures analysis of variance ( α = 0.05). Non‐post‐cured specimens showed perceptible but clinically acceptable color changes. Microhardness decreased after staining in all groups, regardless of curing. Gloss significantly diminished post‐staining, with the control group printed at 45° showing superior retention. Printing orientation influenced color stability, with the 0° orientation showing the highest stability. Post‐curing enhanced color stability and gloss retention in definitive 3D‐printed resins. Printing orientation affected optical outcomes, emphasizing the importance of optimizing both parameters for long‐term esthetic and mechanical reliability.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalComposite ResinsDental MaterialsSurface PropertiesColorHardnessMaterials TestingHumans

Stichwörter der Autor:innen

additive manufacturingcomputer‐aided designdental crowndental materials

Substanzen

Composite ResinsDental Materials

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Institute of Science and Technology, São Paulo State University (UNESP), São José dos Campos, Brazil.
  • Department of Restorative Dentistry and Prosthodontics, School of Dentistry, Universidad Espíritu Santo, Samborondón, Ecuador.

ORCID-Profile: Luana Dos Santos Souza, Andrea Mendoza, Taciana Marco Ferraz Caneppele, Pablo Lenin Benitez Sellan, Eduardo Bresciani

Förderung

  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Zitieren

APA

Souza, L. D. S., Mendoza, A., Caneppele, T. M. F., Benitez Sellan, P. L., & Bresciani, E. (2026). Influence of printing orientation and post‐curing on optical and surface properties of definitive three‐dimensional‐printed dental resin with inorganic fillers. European Journal of Oral Sciences, 134(4). https://doi.org/10.1111/eos.70083

Vancouver

Souza LDS, Mendoza A, Caneppele TMF, Benitez Sellan PL, Bresciani E. Influence of printing orientation and post‐curing on optical and surface properties of definitive three‐dimensional‐printed dental resin with inorganic fillers. European Journal of Oral Sciences. 2026;134(4). doi:10.1111/eos.70083

BibTeX
@article{Souza2026,
  author = {Souza, Luana Dos Santos and Mendoza, Andrea and Caneppele, Taciana Marco Ferraz and Benitez Sellan, Pablo Lenin and Bresciani, Eduardo},
  title = {Influence of printing orientation and post‐curing on optical and surface properties of definitive three‐dimensional‐printed dental resin with inorganic fillers},
  journal = {European Journal of Oral Sciences},
  year = {2026},
  volume = {134},
  number = {4},
  doi = {10.1111/eos.70083}
}
Kostenlos starten →