EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evaluation of a 3D‐Printed Model as Complete Case Scenario in Undergraduate Dental Education—Diagnosis, Treatment Planning and Clinical Practice

Sebastian Bürklein iD, Edgar Schäfer, David Donnermeyer

European Journal of Dental Education · 2026

DOI: 10.1111/eje.13100 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Dental Education, 2026. Verfasst von Sebastian Bürklein und 2 weiteren Autor:innen. Beteiligte Einrichtung: Central Interdisciplinary Ambulance in the School of Dentistry, University of Münster, Münster, Germany. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Education, Dental, Patient Care Planning, Models, Dental. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Ministry of Innovation, Science and Research of North Rhine-Westphalia..

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

3D‐printed teeth/models are important adjuncts in dental education. Nevertheless, there is a lack of simulated cases to learn and understand complex treatment scenarios, including anamnesis, diagnosis, treatment planning and therapy. Material and Methods Third‐year students ( n = 44) received a complete 3D‐printed model (upper and lower jaw) of a patient who needed emergency treatment. Based on the information provided (i) general history, (ii) specific dental history, (iii) radiographs, the students made a diagnosis and planned the treatment, which they performed independently under supervision. The case included periodontal, restorative, endodontic and surgical treatments and semi‐permanent splinting. Using a 3‐ or 5‐point Likert scale, students rated each treatment episode, the learning outcome and the impact of the model on training using a questionnaire. Chi‐square test served for statistical analysis.

Results

The majority (63.6%) stated that the interdisciplinary model allowed a better learning effect than the approach dealing with each section separately ( p < 0.05). Almost all students rated the diagnostic process as excellent (88.0%–95.5%), as the general history, dental history and radiographs were consistent with the clinical findings. Periodontal therapy was rated significantly lower compared to all other areas ( p < 0.05). For endodontic treatment, the students disagreed, abstaining from practising on extracted human teeth. However, the students felt confident to perform all treatment steps in the following clinical courses.

Conclusion

Customised, interdisciplinary 3D‐printed teaching models covering complex treatment strategies were best suited to enhance dental students' skills and foster their enthusiasm for the integrated diagnosis and treatment planning process. Their implementation into dental education is strongly recommended to improve both training and future patient care.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalEducation, DentalPatient Care PlanningModels, DentalHumansClinical CompetenceStudents, Dental

Stichwörter der Autor:innen

3D printingdental educationdental studentsdigital learningdigital technologysimulation traininguniversal digital dental models

Autor:innen und Institutionen

  • Central Interdisciplinary Ambulance in the School of Dentistry, University of Münster, Münster, Germany.
  • Department of Restorative, Preventive and Pediatric Dentistry, ZMK Bern, University of Bern, Bern, Switzerland.

ORCID-Profile: Sebastian Bürklein

Förderung

  • The Ministry of Innovation, Science and Research of North Rhine-Westphalia.

Zitieren

APA

Bürklein, S., Schäfer, E., & Donnermeyer, D. (2026). Evaluation of a 3D‐Printed Model as Complete Case Scenario in Undergraduate Dental Education—Diagnosis, Treatment Planning and Clinical Practice. European Journal of Dental Education. https://doi.org/10.1111/eje.13100

Vancouver

Bürklein S, Schäfer E, Donnermeyer D. Evaluation of a 3D‐Printed Model as Complete Case Scenario in Undergraduate Dental Education—Diagnosis, Treatment Planning and Clinical Practice. European Journal of Dental Education. 2026. doi:10.1111/eje.13100

BibTeX
@article{Brklein2026,
  author = {Bürklein, Sebastian and Schäfer, Edgar and Donnermeyer, David},
  title = {Evaluation of a 3D‐Printed Model as Complete Case Scenario in Undergraduate Dental Education—Diagnosis, Treatment Planning and Clinical Practice},
  journal = {European Journal of Dental Education},
  year = {2026},
  doi = {10.1111/eje.13100}
}
Kostenlos starten →