EUVIMEDEUVIMED entdecken
Open Access

The Effect of 3D Printed Models on the Ability of Dental Students to Locate the Second Mesiobuccal Canal in Maxillary First Molars

Eda Gürsu Şahin iD, Remzi Orkun Akgün iD

Journal of Dental Education · 2025

DOI: 10.1002/jdd.70092 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Dental Education, 2025. Verfasst von Eda Gürsu Şahin und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Endodontics at the Faculty of Dentistry, Cankiri Karatekin University, Çankırı, Turkey. Hauptthemen laut MEDLINE: Molar, Printing, Three-Dimensional, Dental Pulp Cavity, Students, Dental. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

Endodontic treatment is one of the final options aimed at preserving a tooth before extraction. The complex root canal anatomy of maxillary first molars (MFMs), particularly the detection of the second canal located in the mesiobuccal root, presents a significant clinical challenge. This study evaluates the influence of 3D‐printed MFM models on the ability of dental students to identify the second mesiobuccal (MB2) canal.

Methods

A total of 50 dental students who had completed their preclinical endodontic training were included in the study. In the first phase, standardized 3D printed models (3DPMs) were given to the students, who were then instructed to perform access cavity preparations and locate the root canals. Subsequently, a theoretical lecture on the morphology of the MB2 canal was delivered using digital 3D visualizations, supported by an enlarged 3DPM magnified fivefold. Following the theoretical training, the same procedure was repeated using new models. Participants’ feedback was collected through a five‐point Likert scale questionnaire.

Results

Prior to the training, only one student was able to accurately identify the MB2 canal; however, this number increased significantly following the educational intervention ( p < 0.001). A total of 96% of the participants reported that the 3DPM were effective in distinguishing canal locations, and 100% indicated that the models contributed educationally to their understanding of endodontic anatomy.

Conclusion

Educational materials based on 3D printing technology enhance the effectiveness of preclinical endodontic training and improve students’ ability to perceive and identify complex root canal anatomies.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

MolarPrinting, Three-DimensionalDental Pulp CavityStudents, DentalEducation, DentalModels, DentalEndodonticsHumansMaxillaClinical Competence

Stichwörter der Autor:innen

3D printingdental educationmaxillar first molar

Autor:innen und Institutionen

  • Department of Endodontics at the Faculty of Dentistry, Cankiri Karatekin University, Çankırı, Turkey.
  • Department of Basic Sciences at the Faculty of Dentistry, Cankiri Karatekin University, Çankırı, Turkey.

ORCID-Profile: Eda Gürsu Şahin, Remzi Orkun Akgün

Zitieren

APA

Gürsu Şahin, E., & Akgün, R. O. (2025). The Effect of 3D Printed Models on the Ability of Dental Students to Locate the Second Mesiobuccal Canal in Maxillary First Molars. Journal of Dental Education. https://doi.org/10.1002/jdd.70092

Vancouver

Gürsu Şahin E, Akgün RO. The Effect of 3D Printed Models on the Ability of Dental Students to Locate the Second Mesiobuccal Canal in Maxillary First Molars. Journal of Dental Education. 2025. doi:10.1002/jdd.70092

BibTeX
@article{Grsuahin2025,
  author = {Gürsu Şahin, Eda and Akgün, Remzi Orkun},
  title = {The Effect of 3D Printed Models on the Ability of Dental Students to Locate the Second Mesiobuccal Canal in Maxillary First Molars},
  journal = {Journal of Dental Education},
  year = {2025},
  doi = {10.1002/jdd.70092}
}
Kostenlos starten →