EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evaluating the Effectiveness of 3D‐Printed Models in Tooth Morphology Training for Students

Ivet Dzhondrova iD, Ilia Liondev iD, Hristina Galeva iD, Todor Bogdanov iD, Todor Uzunov iD, Dimitar Kirov iD

Journal of Dental Education · 2026

DOI: 10.1002/jdd.70182 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Dental Education, 2026. Verfasst von Ivet Dzhondrova und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthetic Dental Medicine, Faculty of Dental Medicine, Medical University, Sofia, Bulgaria. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Education, Dental, Tooth, Models, Dental. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union, European Union-NextGenerationEU, European Commission.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose/Objectives Tooth morphology is a fundamental aspect of dental education, essential for various clinical disciplines. Traditional teaching methods, such as 2D visualizations, gypsum models, and wax or soap carving, have been widely used to develop students’ spatial understanding and manual skills. However, the integration of 3D‐printed models offers a novel approach that may enhance learning by providing a more accurate representation of dental morphology. This study aimed to assess the effectiveness of 3D‐printed models in learning tooth morphology by comparing their impact on students' practical and theoretical performance with traditional teaching methods.

Methods

Dental students were divided into two groups: one utilizing 3D‐printed models alongside traditional methods and another relying solely on conventional gypsum and 2D visualizations. Practical assessments included soap tooth carving and wax modelling, while theoretical knowledge was evaluated through a written examination. Additionally, students completed a questionnaire to provide feedback on their experience with the 3D‐printed models.

Results

Students who used 3D‐printed models achieved significantly higher scores in the soap tooth carving task, demonstrating improved accuracy and anatomical detail. However, there was no significant difference in the wax modelling scores between the two groups, suggesting that advanced manual dexterity skills are not solely dependent on 3D visualization. Theoretical examination results also showed no significant difference, indicating that 3D models primarily enhance practical skills rather than theoretical comprehension. Over 80% of students reported that 3D‐printed models were highly beneficial in understanding tooth anatomy and improving carving skills. Conclusion(s) The findings suggest that 3D‐printed models serve as a valuable tool for enhancing practical skills in dental education. While they do not replace traditional methods, they effectively support hands‐on learning and visualization.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalEducation, DentalToothModels, DentalHumansStudents, DentalModels, Anatomic

Stichwörter der Autor:innen

3D printing3D‐printed teethdental educationdental modelstooth morphology

Autor:innen und Institutionen

  • Department of Prosthetic Dental Medicine, Faculty of Dental Medicine, Medical University, Sofia, Bulgaria.
  • Department of Physics and Biophysics, Medical University, Sofia, Bulgaria.

ORCID-Profile: Ivet Dzhondrova, Ilia Liondev, Hristina Galeva, Todor Bogdanov, Todor Uzunov, Dimitar Kirov

Förderung

  • European Union
  • European Union-NextGenerationEU
  • European Commission

Zitieren

APA

Dzhondrova, I., Liondev, I., Galeva, H., Bogdanov, T., Uzunov, T., & Kirov, D. (2026). Evaluating the Effectiveness of 3D‐Printed Models in Tooth Morphology Training for Students. Journal of Dental Education. https://doi.org/10.1002/jdd.70182

Vancouver

Dzhondrova I, Liondev I, Galeva H, Bogdanov T, Uzunov T, Kirov D. Evaluating the Effectiveness of 3D‐Printed Models in Tooth Morphology Training for Students. Journal of Dental Education. 2026. doi:10.1002/jdd.70182

BibTeX
@article{Dzhondrova2026,
  author = {Dzhondrova, Ivet and Liondev, Ilia and Galeva, Hristina and Bogdanov, Todor and Uzunov, Todor and Kirov, Dimitar},
  title = {Evaluating the Effectiveness of 3D‐Printed Models in Tooth Morphology Training for Students},
  journal = {Journal of Dental Education},
  year = {2026},
  doi = {10.1002/jdd.70182}
}
Kostenlos starten →