EUVIMEDEUVIMED entdecken
Crossref

Microgap Formation in Conical Implant‐Abutment Connections Under Oblique Loading: Influence of Cone Angle Mismatch Through Finite Element Analysis

Marlene Kasumi Gantier-Takano iD, Yiyun Xing, Ning Ye, Conrado Aparicio iD, Carlos Navarro Cuéllar iD, Josete Barbosa Cruz Meira iD, Alex Siu Lun Fok iD

Clinical Implant Dentistry and Related Research · 2025

DOI: 10.1111/cid.13436 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Implant Dentistry and Related Research, 2025. Verfasst von Marlene Kasumi Gantier-Takano und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Dentistry, Department of Biomaterials and Oral Biology, University of São Paulo, São Paulo, Brazil. Hauptthemen laut MEDLINE: Dental Stress Analysis, Dental Implant-Abutment Design, Dental Abutments, Dental Implants. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 53 Literaturangaben. Gefördert von: Mozo-Grau SA, Valladolid, Spain, 3Mgives KOL Scholarship (for Yiyun Xing), CAPES scholarship (for Marlene Kasumi Gantier-Takano).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

This study evaluated different designs of the conical implant‐abutment connection (IAC) and their resistance to microgap formation under oblique loads as specified by the ISO standard for testing dental implants. Also evaluated was the effect of deviations from the ISO specifications on the outcomes.

Methods

Finite element analysis was conducted to compare the microgap formation and stress distribution among three conical IAC designs (A, B, and C) in two loading configurations: one compliant with ISO 14801 and one with a modified load adaptor (non‐ISO). The different IAC designs varied in the taper, diameter, and cone height. The cone angle mismatch (Cam) between the implant and abutment was considered. A torque of 20 Ncm and oblique loads (up to 400 N) were simulated.

Results

The stresses produced by the screw‐tightening torque varied among the different IAC designs. The contact height was approximately 0.3 mm for Designs A and B, and less than 0.03 mm for Design C. Under oblique loads, Design A maintained IAC sealing without gap formation up to 400 N. With the ISO adaptor, gaps appeared in Design B at 300 N and in Design C at 90 N. The non‐ISO adaptor resulted in gap formation at 160 N for Design B and at 50 N for Design C.

Conclusions

The IAC design and cone angle mismatch significantly influenced microgap formation, with some designs showing zero gaps even when the oblique load reached 400 N. The non‐ISO adaptor increased gap formation in IACs B and C.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental Stress AnalysisDental Implant-Abutment DesignDental AbutmentsDental ImplantsFinite Element AnalysisTorqueHumansStress, Mechanical

Stichwörter der Autor:innen

dental implant‐abutments designdimensional measurement accuracyfinite element analysismechanicalperi‐implantitisstress

Substanzen

Dental Implants

Autor:innen und Institutionen

  • School of Dentistry, Department of Biomaterials and Oral Biology, University of São Paulo, São Paulo, Brazil.
  • Minnesota Dental Research Center for Biomaterials and Biomechanics, School of Dentistry, University of Minnesota, Minneapolis, Minnesota, USA.
  • Department of Research, Faculty of Dentistry, Universitat Internacional de Catalunya, Barcelona, Spain.
  • Catalan Institute for Research and Advanced Studies (ICREA), Barcelona, Spain.
  • Institute for Bioengineering of Catalonia (IBEC), Barcelona Institute of Science and Technology (BIST), Barcelona, Spain.
  • Maxillofacial Surgery Department, Hospital Gregorio Marañón, Madrid, Spain.

ORCID-Profile: Marlene Kasumi Gantier-Takano, Conrado Aparicio, Carlos Navarro Cuéllar, Josete Barbosa Cruz Meira, Alex Siu Lun Fok

Förderung

  • Mozo-Grau SA, Valladolid, Spain
  • 3Mgives KOL Scholarship (for Yiyun Xing)
  • CAPES scholarship (for Marlene Kasumi Gantier-Takano)

Zitieren

APA

Gantier-Takano, M. K., Xing, Y., Ye, N., Aparicio, C., Navarro Cuéllar, C., Meira, J. B. C., & Fok, A. S. L. (2025). Microgap Formation in Conical Implant‐Abutment Connections Under Oblique Loading: Influence of Cone Angle Mismatch Through Finite Element Analysis. Clinical Implant Dentistry and Related Research. https://doi.org/10.1111/cid.13436

Vancouver

Gantier-Takano MK, Xing Y, Ye N, Aparicio C, Navarro Cuéllar C, Meira JBC, et al. Microgap Formation in Conical Implant‐Abutment Connections Under Oblique Loading: Influence of Cone Angle Mismatch Through Finite Element Analysis. Clinical Implant Dentistry and Related Research. 2025. doi:10.1111/cid.13436

BibTeX
@article{GantierTakano2025,
  author = {Gantier-Takano, Marlene Kasumi and Xing, Yiyun and Ye, Ning and Aparicio, Conrado and Navarro Cuéllar, Carlos and Meira, Josete Barbosa Cruz and Fok, Alex Siu Lun},
  title = {Microgap Formation in Conical Implant‐Abutment Connections Under Oblique Loading: Influence of Cone Angle Mismatch Through Finite Element Analysis},
  journal = {Clinical Implant Dentistry and Related Research},
  year = {2025},
  doi = {10.1111/cid.13436}
}
Kostenlos starten →