EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The influence of different cement spaces on the marginal gap of lithium disilicate crowns constructed by two scanner and milling unit combinations

J Dudley iD, J Xu

Australian Dental Journal · 2024

DOI: 10.1111/adj.13014 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Australian Dental Journal, 2024. Verfasst von J Dudley und 1 weiteren Autor:innen. Beteiligte Einrichtung: Adelaide Dental School, The University of Adelaide, Adelaide, SA, Australia. Hauptthemen laut MEDLINE: Crowns, Dental Porcelain, Computer-Aided Design, Dental Prosthesis Design. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Australian Prosthodontics Society Research Grant.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

This study compared the marginal gaps of CAD/CAM lithium disilicate (LDS) crowns constructed using a contemporary and older scanner/milling unit combination at three different cement spaces.

Methods

Twenty‐four undergraduate students prepared a Columbia model lower left first molar for an LDS crown in a simulated environment. From each crown preparation, one LDS crown was constructed using an E4D scanner/E4D milling unit (E4DS/E4DM) and TRIOS 3 scanner/Sirona inLab MC X5 milling unit (TRIO/MCX5) at cement space settings of 50, 100 and 200 μm. Each LDS crown was positioned onto the original crown preparation, and then a stereomicroscope was used to make three vertical marginal gap measurements at four locations (mid‐buccal, mid‐lingual, mid‐mesial and mid‐distal). The mean marginal gap (MMG) was calculated for each crown and each individual tooth surface.

Results

The MMGs of CAD/CAM LDS crowns constructed by TRIO/MCX5 were 72.31 at 50, 63.73 at 100 μm and 46.23 μm at 200 μm, which were smaller than E4DS/E4DM at each cement space.

Conclusions

Increasing the cement space decreased the MMG in both scanner/milling unit combinations. The smallest MMG was found using the newer scanner/milling unit at the 200 μm cement space. © 2024 Australian Dental Association.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsDental PorcelainComputer-Aided DesignDental Prosthesis DesignDental Marginal AdaptationHumansDental CementsMolar

Stichwörter der Autor:innen

Marginal gapcrownlithium disilicatemilling unitscanning

Substanzen

lithia disilicateDental PorcelainDental Cements

Autor:innen und Institutionen

  • Adelaide Dental School, The University of Adelaide, Adelaide, SA, Australia.

ORCID-Profile: J Dudley

Förderung

  • The Australian Prosthodontics Society Research Grant

Zitieren

APA

Dudley, J., & Xu, J. (2024). The influence of different cement spaces on the marginal gap of lithium disilicate crowns constructed by two scanner and milling unit combinations. Australian Dental Journal. https://doi.org/10.1111/adj.13014

Vancouver

Dudley J, Xu J. The influence of different cement spaces on the marginal gap of lithium disilicate crowns constructed by two scanner and milling unit combinations. Australian Dental Journal. 2024. doi:10.1111/adj.13014

BibTeX
@article{Dudley2024,
  author = {Dudley, J and Xu, J},
  title = {The influence of different cement spaces on the marginal gap of lithium disilicate crowns constructed by two scanner and milling unit combinations},
  journal = {Australian Dental Journal},
  year = {2024},
  doi = {10.1111/adj.13014}
}
Kostenlos starten →