Characterization of L-PBF Printed AISI 316L Parts: Dimensional accuracy, surface quality, microstructural and mechanical behaviors
Materials Research Express · 20.11.2026
DOI: 10.1088/2053-1591/aec545 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials Research Express, online erschienen am 20.11.2026. Verfasst von Aysu Hande Yucel und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bilimsel Araştırma Projeleri Birimi, İstanbul Teknik Üniversitesi.
Abstract (Originalsprache)
This study investigates components manufactured using low volumetric energy density (VED) in laser powder bed fusion (L-PBF) additive manufacturing, specifically for preliminary prototyping. In industrial contexts, tangible prototypes play a vital role in identifying potential design flaws before assembly and production. To evaluate the influence of low and high VEDs, AISI 316L stainless steel specimens were produced at two speeds while maintaining constant laser power: 300 mm/s and 1500 mm/s, corresponding to VEDs of 80 J/mm³ (high-VED) and 16 J/mm³ (low-VED), respectively. Only the scanning speed was varied, while the laser power (90 W), hatch distance (150 µm), and layer thickness (25 µm) were kept constant. The effect of scanning speed, expressed through VED, was evaluated on four responses: geometric accuracy, surface roughness, porosity, and mechanical properties. Increasing VED from 16 to 80 J/mm³ increased the flatness deviation of all matchbox specimens, mostly for the 2.3 mm-thick specimen (from approximately 1.71% to 6.96%), and increased the angular deviation of the triangular prisms by approximately 1.18–6.88 pp, depending on the angle. In contrast, circularity deviations decreased slightly for all cylindrical features, with the largest decrease observed on the outer surface of the smaller hollow tube (with an inner radius of 1.4 mm and an outer radius of 2.3 mm) from 5.05% to 4.07%, while cylindricity exhibited a more geometry-dependent response for the same tube, decreasing from 30.45% to 28.81%. Surface roughness decreased by approximately 40% at higher VED, with Ra decreasing from 13.41 to 8.03 µm for the dogbone specimens and from 17.05 to 9.98 µm for the hemisphere specimens. Micro-computed tomography revealed substantially higher XCT-resolved porosity in the low-VED specimen (~1.49%) compared with the high-VED specimen (0.17%). Tensile testing showed that the specimen produced at 80 J/mm³ achieved an ultimate tensile strength of 684.0 ± 7.2 MPa, compared with 120.5 ± 16.2 MPa for the specimen produced at 16 J/mm³, corresponding to an approximately 5.7-fold increase. Under the low-VED condition, flatness deviations ranged from approximately 1.71% to 6.11% and angular deviations from 4.68% to 15.16%. The fivefold increase in scanning speed reduces scanning time but compromises density, surface quality, and strength. Therefore, the suitability of this condition for preliminary prototyping should be assessed against the dimensional tolerances and functional requirements of the intended application rather than assumed to be universally acceptable.
Keywords: Laser powder bed fusion, Surface roughness, Computed tomography, Mechanical properties, dimensional accuracy.
Förderung
- Bilimsel Araştırma Projeleri Birimi, İstanbul Teknik Üniversitesi
Zitieren
APA
Yucel, A. H., Kuzu, A. T., Yildiz, R. A., Malekan, M., & Bakkal, M. (2026). Characterization of L-PBF Printed AISI 316L Parts: Dimensional accuracy, surface quality, microstructural and mechanical behaviors. Materials Research Express. https://doi.org/10.1088/2053-1591/aec545
Vancouver
Yucel AH, Kuzu AT, Yildiz RA, Malekan M, Bakkal M. Characterization of L-PBF Printed AISI 316L Parts: Dimensional accuracy, surface quality, microstructural and mechanical behaviors. Materials Research Express. 2026. doi:10.1088/2053-1591/aec545
BibTeX
@article{Yucel2026,
author = {Yucel, Aysu Hande and Kuzu, Ali Taner and Yildiz, Rasid Ahmed and Malekan, Mohammad and Bakkal, Mustafa},
title = {Characterization of L-PBF Printed AISI 316L Parts: Dimensional accuracy, surface quality, microstructural and mechanical behaviors},
journal = {Materials Research Express},
year = {2026},
doi = {10.1088/2053-1591/aec545}
}
EUVIMED