EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

To BPE or not to BPE: Neutron tenth-value layers in polyethylene with variable boron content for LINAC shielding

M Bellamy iD, A Jinia, L Carter iD, B Quinn iD, A Pérez-Andújar, B Chu iD, L Dauer iD

Journal of Radiological Protection · 2026

DOI: 10.1088/1361-6498/ae490e ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Radiological Protection, 2026. Verfasst von M Bellamy und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Medical Physics, Memorial Sloan Kettering Cancer Center, New York, NY, United States of America. Hauptthemen laut MEDLINE: Polyethylene, Neutrons, Radiation Protection, Particle Accelerators. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Institutes of Health/National Cancer Institute Cancer Center.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Borated polyethylene is an effective neutron moderator and absorber in medical linear accelerator shielding; however, there is limited data regarding the required material thickness for adequate neutron attenuation. To address the gap in shielding data, our study systematically quantifies first and equilibrium tenth-value layers (TVL1 and TVLe) for polyethylene containing 0%, 5% and 30% natural boron by weight across neutron energies ranging from thermal to fast. Comprehensive Monte Carlo simulations (n = 3504) were performed to estimate TVL thicknesses from thermal to 20 MeV neutrons. A current tally was used to count neutrons exiting the shield and determine thicknesses corresponding to 10% and 1% transmission. Sixteen energies and 73 thicknesses of materials were modelled with statistical uncertainties below 3%. TVL thicknesses were independently validated with PHITS using identical simulation parameters. We found that TVL values ranged from 1.3 mm for thermal neutrons in borated polyethylene, to 50 cm for 20 MeV neutrons in pure polyethylene. In all cases, adding boron to polyethylene reduced the TVL, with the greatest effect at thermal energies, and a smallest effect at 12 MeV. Here we provide the first comprehensive characterization of borated polyethylene's ability to attenuate neutrons, supporting shielding design for medical linear accelerators.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyethyleneNeutronsRadiation ProtectionParticle AcceleratorsBoronMonte Carlo Method

Stichwörter der Autor:innen

LINAC shieldingboron content optimisationmedical physicsneutron attenuationradiation safetyradiotherapy facility design

Substanzen

PolyethyleneBoron

Autor:innen und Institutionen

  • Department of Medical Physics, Memorial Sloan Kettering Cancer Center, New York, NY, United States of America.

ORCID-Profile: M Bellamy, L Carter, B Quinn, B Chu, L Dauer

Förderung

  • National Institutes of Health/National Cancer Institute Cancer Center

Zitieren

APA

Bellamy, M., Jinia, A., Carter, L., Quinn, B., Pérez-Andújar, A., Chu, B., & Dauer, L. (2026). To BPE or not to BPE: Neutron tenth-value layers in polyethylene with variable boron content for LINAC shielding. Journal of Radiological Protection. https://doi.org/10.1088/1361-6498/ae490e

Vancouver

Bellamy M, Jinia A, Carter L, Quinn B, Pérez-Andújar A, Chu B, et al. To BPE or not to BPE: Neutron tenth-value layers in polyethylene with variable boron content for LINAC shielding. Journal of Radiological Protection. 2026. doi:10.1088/1361-6498/ae490e

BibTeX
@article{Bellamy2026,
  author = {Bellamy, M and Jinia, A and Carter, L and Quinn, B and Pérez-Andújar, A and Chu, B and Dauer, L},
  title = {To BPE or not to BPE: Neutron tenth-value layers in polyethylene with variable boron content for LINAC shielding},
  journal = {Journal of Radiological Protection},
  year = {2026},
  doi = {10.1088/1361-6498/ae490e}
}
Kostenlos starten →