EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D-Printed Polycaprolactone/Alginate-Whitlockite Composite Scaffolds for Bioactive Bone Tissue Engineering

Sura Ali Al-Nidawi, Aliakbar Najafinezhad, Hossein Abbastabar Ahangar, Hamid Reza Bakhsheshi-Rad iD, Jaroslaw W Drelich

ACS Materials Au · 11.11.2026 · 6 (6) · 1540-1555

DOI: 10.1021/acsmaterialsau.6c00160 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Materials Au, online erschienen am 08.10.2026. Verfasst von Sura Ali Al-Nidawi und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Engineering, Na.C., Islamic Azad University, Najafabad , Iran. Die Arbeit nennt 59 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Despite advances in 3D printing, achieving simultaneous mechanical stability and biological functionality in polymer-based scaffolds remains challenging for bone tissue engineering applications. In this study, 3D-printed scaffolds fabricated from a polycaprolactone/alginate (PCL/Alg) composite reinforced with different amounts of whitlockite (WL) nanoparticles (including 0, 5, 10, 20, and 30 wt %) were designed. Mechanical studies showed that adding 5 wt % WL significantly improved the mechanical properties, with the compressive strength and elastic modulus increasing from about 7 and 12 MPa to 22 and 48 MPa, respectively. However, increasing the WL content beyond this value reduced mechanical performance, likely due to WL particle aggregation and disruption of the PCL/Alg scaffold. Water contact angle analysis showed that the PCL/Alg scaffold incorporated with WL exhibited better hydrophilicity than pure PCL and PCL/Alg, which was mainly attributed to the hydrophilic nature of these compounds. Immersion results indicated that adding WL facilitated apatite deposition, mainly through the release of calcium and magnesium ions. The MTT assay showed that none of the designed scaffolds was toxic to MG-63 cells. Meanwhile, the scaffold containing 5 wt % WL exhibited the highest cell viability and adhesion, whereas higher WL concentrations yielded less favorable cellular responses. Taken together, the results obtained indicate that the PCL/Alg scaffold containing 5% WL provides a balanced combination of mechanical and biological properties, making it a desirable bioactive platform for bone tissue engineering applications.

Schlagwörter

Stichwörter der Autor:innen

3D printing scaffoldalginatebioactivitybiocompatibilitybone tissue engineeringmechanical propertieswhitlockite

Autor:innen und Institutionen

  • Department of Materials Engineering, Na.C., Islamic Azad University, Najafabad , Iran.
  • Department of Chemistry, Na.C., Islamic Azad University, Najafabad , Iran.
  • Department of Materials Science and Engineering, Michigan Technological University, Houghton, Michigan 49931, United States.
  • Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia.

ORCID-Profile: Hamid Reza Bakhsheshi-Rad

Zitieren

APA

Al-Nidawi, S. A., Najafinezhad, A., Ahangar, H. A., Bakhsheshi-Rad, H. R., & Drelich, J. W. (2026). 3D-Printed Polycaprolactone/Alginate-Whitlockite Composite Scaffolds for Bioactive Bone Tissue Engineering. ACS Materials Au, 6(6), 1540-1555. https://doi.org/10.1021/acsmaterialsau.6c00160

Vancouver

Al-Nidawi SA, Najafinezhad A, Ahangar HA, Bakhsheshi-Rad HR, Drelich JW. 3D-Printed Polycaprolactone/Alginate-Whitlockite Composite Scaffolds for Bioactive Bone Tissue Engineering. ACS Materials Au. 2026;6(6):1540-1555. doi:10.1021/acsmaterialsau.6c00160

BibTeX
@article{AlNidawi2026,
  author = {Al-Nidawi, Sura Ali and Najafinezhad, Aliakbar and Ahangar, Hossein Abbastabar and Bakhsheshi-Rad, Hamid Reza and Drelich, Jaroslaw W},
  title = {3D-Printed Polycaprolactone/Alginate-Whitlockite Composite Scaffolds for Bioactive Bone Tissue Engineering},
  journal = {ACS Materials Au},
  year = {2026},
  volume = {6},
  number = {6},
  pages = {1540--1555},
  doi = {10.1021/acsmaterialsau.6c00160}
}
Kostenlos starten →