EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface modification of 3D ‐printed polycaprolactone scaffolds with silk fibroin for bone tissue engineering

Hamed Koeini, Esmaeil Biazar, Davood Zaeifi, Reza Zeinali iD, Saeed Heidari-Keshel, Amimasoud Hassanour, Helia Saheli, Arezou Mehrabi

FEBS Open Bio · 09.11.2026

DOI: 10.1002/2211-5463.70366 ↗

Kurz gefasst

Fachartikel in der Zeitschrift FEBS Open Bio, online erschienen am 09.11.2026. Verfasst von Hamed Koeini und 7 weiteren Autor:innen. Beteiligte Einrichtung: Biomaterials and Tissue Engineering Group, Department of Biomedical Engineering, To.C., Islamic Azad University, Tonekabon, Iran. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

One innovative design for tissue‐engineering scaffolds uses 3D printing technology. Here, we used polycaprolactone (PCL) filament as a biocompatible material to design a porous 3D scaffold for bone tissue engineering. After surface modification with silk fibroin, the samples were analyzed using various techniques, including structural characterization, morphological analysis, wettability assessment, cytotoxicity testing, and cell adhesion assays. Scanning electron microscope images showed that the samples were successfully fabricated and exhibited a well‐structured porous architecture. Structural analysis confirmed the presence of a silk fibroin coating on the surfaces of the PCL filaments. Contact angle measurements showed that the control PCL sample, with a contact angle of 73°, decreased to approximately 52° after surface modification with silk fibroin, indicating enhanced hydrophilicity of the scaffolds postmodification. The MTT assay results demonstrated that the modified samples exhibited no cytotoxicity, while electron microscopy images showed good cell adhesion. In general, the surface modification of 3D‐printed PCL scaffolds with silk fibroin represents a promising approach for developing suitable scaffolds for bone tissue engineering applications.

Schlagwörter

Stichwörter der Autor:innen

3D printed scaffoldbone tissue engineeringpolycaprolactonesilk fibroinsurface modification

Autor:innen und Institutionen

  • Biomaterials and Tissue Engineering Group, Department of Biomedical Engineering, To.C., Islamic Azad University, Tonekabon, Iran.
  • Department of Medical Biotechnology and Nanotechnology, Faculty of Medicine, Mashhad University of Medical Sciences, Mashhad, Iran.
  • Group of Molecular and Industrial Biotechnology, Department of Chemical Engineering, Universität Politècnica de Catalunya, Terrassa, Spain.
  • Hematopoietic Stem Cell Research Center, Shahid Beheshti University of Medical Sciences, Tehran, Iran.
  • Department of Medicine, To.C., Islamic Azad University, Tonekabon, Iran.

ORCID-Profile: Reza Zeinali

Zitieren

APA

Koeini, H., Biazar, E., Zaeifi, D., Zeinali, R., Heidari-Keshel, S., Hassanour, A., Saheli, H., & Mehrabi, A. (2026). Surface modification of 3D ‐printed polycaprolactone scaffolds with silk fibroin for bone tissue engineering. FEBS Open Bio. https://doi.org/10.1002/2211-5463.70366

Vancouver

Koeini H, Biazar E, Zaeifi D, Zeinali R, Heidari-Keshel S, Hassanour A, et al. Surface modification of 3D ‐printed polycaprolactone scaffolds with silk fibroin for bone tissue engineering. FEBS Open Bio. 2026. doi:10.1002/2211-5463.70366

BibTeX
@article{Koeini2026,
  author = {Koeini, Hamed and Biazar, Esmaeil and Zaeifi, Davood and Zeinali, Reza and Heidari-Keshel, Saeed and Hassanour, Amimasoud and Saheli, Helia and Mehrabi, Arezou},
  title = {Surface modification of 3D ‐printed polycaprolactone scaffolds with silk fibroin for bone tissue engineering},
  journal = {FEBS Open Bio},
  year = {2026},
  doi = {10.1002/2211-5463.70366}
}
Kostenlos starten →