Synergistic Fire Resistance of Nanobrick Wall Coated 3D Printed Photopolymer Lattices
ACS Applied Materials & Interfaces · 29.03.2023 · 15 (12) · 16046-16054
DOI: 10.1021/acsami.3c00177 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 16.03.2023. Verfasst von Thomas J Kolibaba und 7 weiteren Autor:innen. Beteiligte Einrichtung: Applied Chemicals and Materials Division, National Institute of Standards and Technology, Boulder, Colorado 80305, United States. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: Intramural NIST DOC.
Abstract (Originalsprache)
Photopolymer additive manufacturing has become the subject of widespread interest in recent years due to its capacity to enable fabrication of difficult geometries that are impossible to build with traditional manufacturing methods. The flammability of photopolymer resin materials and the lattice structures enabled by 3D printing is a barrier to widespread adoption that has not yet been adequately addressed. Here, a water-based nanobrick wall coating is deposited on 3D printed parts with simple (i.e., dense solid) or complex (i.e., lattice) geometries. When subject to flammability testing, the printed parts exhibit no melt dripping and a propensity toward failure at the print layer interfaces. Moving from a simple solid geometry to a latticed geometry leads to reduced time to failure during flammability testing. For nonlatticed parts, the coating provides negligible improvement in fire resistance, but coating of the latticed structures significantly increases time to failure by up to ≈340% compared to the uncoated lattice. The synergistic effect of coating and latticing is attributed to the lattice structures' increased surface area to volume ratio, allowing for an increased coating:photopolymer ratio and the ability of the lattice to better accommodate thermal expansion strains. Overall, nanobrick wall coated lattices can serve as metamaterials to increase applications of polymer additive manufacturing in extreme environments.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Applied Chemicals and Materials Division, National Institute of Standards and Technology, Boulder, Colorado 80305, United States.
- Department of Chemistry, Texas A&M University, College Station, Texas 77843, United States.
- Department of Mechanical Engineering, Texas A&M University, College Station, Texas 77843, United States.
- Department of Materials Science and Engineering, Texas A&M University, College Station, Texas 77843, United States.
ORCID-Profile: Thomas J Kolibaba, Callie I Higgins, Zachary N Buck, Jaime C Grunlan, Jason P Killgore
Förderung
- Intramural NIST DOC
Zitieren
APA
Kolibaba, T. J., Iverson, E. T., Legendre, H., Higgins, C. I., Buck, Z. N., Weeks, T. S., Grunlan, J. C., & Killgore, J. P. (2023). Synergistic Fire Resistance of Nanobrick Wall Coated 3D Printed Photopolymer Lattices. ACS Applied Materials & Interfaces, 15(12), 16046-16054. https://doi.org/10.1021/acsami.3c00177
Vancouver
Kolibaba TJ, Iverson ET, Legendre H, Higgins CI, Buck ZN, Weeks TS, et al. Synergistic Fire Resistance of Nanobrick Wall Coated 3D Printed Photopolymer Lattices. ACS Applied Materials & Interfaces. 2023;15(12):16046-16054. doi:10.1021/acsami.3c00177
BibTeX
@article{Kolibaba2023,
author = {Kolibaba, Thomas J and Iverson, Ethan T and Legendre, Hudson and Higgins, Callie I and Buck, Zachary N and Weeks, Timothy S and Grunlan, Jaime C and Killgore, Jason P},
title = {Synergistic Fire Resistance of Nanobrick Wall Coated 3D Printed Photopolymer Lattices},
journal = {ACS Applied Materials & Interfaces},
year = {2023},
volume = {15},
number = {12},
pages = {16046--16054},
doi = {10.1021/acsami.3c00177}
}
EUVIMED