Fabrication trueness and optical, surface, and mechanical properties of additively manufactured polymethyl methacrylate definitive crowns reinforced with silica and titanium oxide nanoparticles: An in vitro study
The Journal of Prosthetic Dentistry · 2026
DOI: 10.1016/j.prosdent.2026.02.013 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026. Verfasst von Rafat Sasany und 1 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Istanbul Biruni University, Istanbul, Turkey. Electronic address: sasanyr@gm…. Hauptthemen laut MEDLINE: Titanium, Polymethyl Methacrylate, Silicon Dioxide, Crowns. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 35 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Additively manufactured (AM) polymethyl methacrylate (PMMA) crowns exhibit limited color stability, suboptimal surface texture, and insufficient strength. The development of effective reinforcement strategies is essential to overcome these shortcomings. PURPOSE: The purpose of this in vitro study was to evaluate the effects of incorporating silica (SiO₂) and titanium dioxide (TiO₂) nanoparticles on the fabrication trueness and the optical, surface, and mechanical properties of AM PMMA crowns. MATERIAL AND METHODS: Mandibular first molar AM PMMA crowns (N=80) were fabricated using 4 materials (n=20 per group): unmodified PMMA (control; FREEPRINT), PMMA with 1 wt% SiO₂ (S), PMMA with 2 wt% TiO₂ (T), and PMMA with a combination of 1 wt% SiO₂ and 2 wt% TiO₂ nanoparticles (ST). Fabrication trueness was evaluated as the root mean square (RMS) surface deviation of the marginal and intaglio surfaces (µm) and their total. Color stability (ΔE₀₀) was assessed using spectrophotometry, and surface roughness (Ra) was measured via noncontact optical profilometry. Wear was assessed by occlusal RMS (µm) after thermomechanical aging; fracture resistance was recorded as peak load to failure (N) on a universal testing machine. Statistical analyses were performed using 1-way ANOVA followed by Bonferroni-adjusted post hoc tests (α=.05). RESULTS: Fabrication trueness differed among groups (marginal, intaglio, and total RMS; all P S>T>ST; qualitative joint evaluation technique (JET) heatmaps showed the same pattern. Fracture load differed (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Istanbul Biruni University, Istanbul, Turkey. Electronic address: sasanyr@gmail.com.
- Assistant Professor, Department of Restorative Dentistry, Faculty of Dentistry, King Abdulaziz University, Jeddah, Saudi Arabia.
Zitieren
APA
Sasany, R., & Al-Johani, H. (2026). Fabrication trueness and optical, surface, and mechanical properties of additively manufactured polymethyl methacrylate definitive crowns reinforced with silica and titanium oxide nanoparticles: An in vitro study. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2026.02.013
Vancouver
Sasany R, Al-Johani H. Fabrication trueness and optical, surface, and mechanical properties of additively manufactured polymethyl methacrylate definitive crowns reinforced with silica and titanium oxide nanoparticles: An in vitro study. The Journal of Prosthetic Dentistry. 2026. doi:10.1016/j.prosdent.2026.02.013
BibTeX
@article{Sasany2026,
author = {Sasany, Rafat and Al-Johani, Hanan},
title = {Fabrication trueness and optical, surface, and mechanical properties of additively manufactured polymethyl methacrylate definitive crowns reinforced with silica and titanium oxide nanoparticles: An in vitro study},
journal = {The Journal of Prosthetic Dentistry},
year = {2026},
doi = {10.1016/j.prosdent.2026.02.013}
}
EUVIMED