EUVIMEDEUVIMED entdecken
Vergleichsstudie

Comparative analysis of surface characteristics and color stability in zirconia-reinforced resin composites: 3D printing, subtractive, and layering techniques

Luiza Freitas Brum Souza, Kétlin Fagundes Teixeira, Ana Carolina Cadore-Rodrigues, Felipe Somavilla Binotto, Luiz Felipe Valandro, Rafael R Moraes, Mutlu Özcan, Gabriel Kalil Rocha Pereira

The Journal of Prosthetic Dentistry · 2026

DOI: 10.1016/j.prosdent.2025.09.013 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Prosthetic Dentistry, 2026. Verfasst von Luiza Freitas Brum Souza und 7 weiteren Autor:innen. Beteiligte Einrichtung: Postdoctoral student, Clinic for Masticatory Disorders and Dental Biomaterials, Center for Dental Medicine, University of Zurich, Zurich, Switzerland. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Zirconium, Composite Resins, Dental Materials. Die Arbeit nennt 55 Literaturangaben. Gefördert von: Finep, Foundation for Research Support of Rio Grande do Sul State, National Council for Scientific and Technological Development.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Despite growing interest in zirconia-reinforced resin composites, the influence of manufacturing techniques on their surface and optical stability remains unclear. PURPOSE: The purpose of this in vitro study was to evaluate the surface characteristics and color stability of zirconia-reinforced resin composite materials produced via 3 techniques: 3-dimensional (3D) printing, subtractive manufacturing, and layering. MATERIAL AND METHODS: Thirty-six disks (Ø10×1.0 mm) were prepared and divided into 3 groups: 3D printing (PriZma 3D Bio Crown; MakertechLabs), subtractive manufacturing (Lava Ultimate; 3M), and layering (Filtek Z350 XT; 3M). Surface properties were assessed using roughness analysis and scanning electron microscopy (SEM). Color coordinates (L*, a*, b*) were recorded using a spectrophotometer (SP60; X-Rite) at baseline, after staining (coffee or red wine for 12 days), and after repolishing (Superfix Dental Finishing & Polishing Disc System; TDV). Statistical analysis included color differences (∆E00) and translucency parameter differences (∆TP00), considering acceptability (AT) and perceptibility thresholds (PT) (α=.05). RESULTS: Three-dimensional printing exhibited higher Ra than subtractive (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalZirconiumComposite ResinsDental MaterialsSurface PropertiesColorMicroscopy, Electron, ScanningIn Vitro TechniquesMaterials TestingHumans

Substanzen

ZirconiumComposite Resinszirconium oxideDental Materialsfiltek Z350

Autor:innen und Institutionen

  • Postdoctoral student, Clinic for Masticatory Disorders and Dental Biomaterials, Center for Dental Medicine, University of Zurich, Zurich, Switzerland.
  • Master's student, Postgraduate Program in Oral Science, Faculty of Dentistry, Center for Development of Advanced Materials, Federal University of Santa Maria (UFSM), Santa Maria, Brazil.
  • Postdoctoral student, Postgraduate Program in Oral Science, Faculty of Dentistry, Center for Development of Advanced Materials, Federal University of Santa Maria (UFSM), Santa Maria, Brazil.
  • Predoctoral student, Faculty of Dentistry, Federal University of Santa Maria (UFSM), Santa Maria, Brazil.
  • Professor, Postgraduate Program in Oral Science, Faculty of Dentistry, Center for Development of Advanced Materials, Federal University of Santa Maria (UFSM), Santa Maria, Brazil.
  • Professor, Graduate Program in Dentistry, School of Dentistry, Federal University of Pelotas (UFPel), Pelotas, Brazil.

Förderung

  • Finep
  • Foundation for Research Support of Rio Grande do Sul State
  • National Council for Scientific and Technological Development
  • Coordination for the improvement of Higher Education Personnel
  • Universidade Federal de Santa Maria

Zitieren

APA

Souza, L. F. B., Teixeira, K. F., Cadore-Rodrigues, A. C., Binotto, F. S., Valandro, L. F., Moraes, R. R., Özcan, M., & Pereira, G. K. R. (2026). Comparative analysis of surface characteristics and color stability in zirconia-reinforced resin composites: 3D printing, subtractive, and layering techniques. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.09.013

Vancouver

Souza LFB, Teixeira KF, Cadore-Rodrigues AC, Binotto FS, Valandro LF, Moraes RR, et al. Comparative analysis of surface characteristics and color stability in zirconia-reinforced resin composites: 3D printing, subtractive, and layering techniques. The Journal of Prosthetic Dentistry. 2026. doi:10.1016/j.prosdent.2025.09.013

BibTeX
@article{Souza2026,
  author = {Souza, Luiza Freitas Brum and Teixeira, Kétlin Fagundes and Cadore-Rodrigues, Ana Carolina and Binotto, Felipe Somavilla and Valandro, Luiz Felipe and Moraes, Rafael R and Özcan, Mutlu and Pereira, Gabriel Kalil Rocha},
  title = {Comparative analysis of surface characteristics and color stability in zirconia-reinforced resin composites: 3D printing, subtractive, and layering techniques},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  doi = {10.1016/j.prosdent.2025.09.013}
}
Kostenlos starten →