Influence of different airborne-particle abrasion pressures, cleaning methods, and artificial aging on zirconia ceramic bonding
The Journal of Prosthetic Dentistry · 2025
DOI: 10.1016/j.prosdent.2025.02.014 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Lisa Türp und 3 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Professor, Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, K…. Hauptthemen laut MEDLINE: Zirconium, Dental Bonding, Ceramics, Dental Etching. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Airborne-particle abrasion (APA) with alumina combined with a primer or luting resin containing a phosphate monomer has been well established for resin bonding to zirconia. However, a standardized method for bonding to zirconia is unavailable, as some factors including the optimal pressure of airborne-particle abrasion, the cleaning method, and the luting resin system are still unclear because of the limited available data. PURPOSE: The purpose of this in vitro study was to evaluate the influence of different airborne-particle abrasion pressures and different cleaning methods of zirconia on the tensile bond strength (TBS) of 2 luting resins system containing methylacryloyloxydecyl-dihydrogenphosphate (MDP) either in the primer or in the luting resin. MATERIAL AND METHODS: A total of 128 disk specimens were milled from zirconia blocks and divided into groups according to the pressure of airborne-particle abrasion of either 0.1 MPa or 0.25 MPa (n=64). The specimens were then divided into 2 subgroups and were either cleaned in an ultrasonic device in isopropanol or with oil-free air stream (n=32). The subgroups were further divided according to the luting resin (n=16) and the bonding surfaces were perpendicularly luted to the acrylic resin tubes filled with a composite resin (Clearfil F II) with either an MDP-containing primer and a luting resin or with a self-adhesive MDP-containing luting resin. Each of the 8 groups was further divided into 2 subgroups (n=8) with either 3-days water storage at 37 °C or 150-days water storage with additional thermal cycling (37 500 thermal cycles between 5 °C and 55 °C) for artificial aging. The TBS was evaluated with a universal testing machine. All specimens underwent failure mode analysis. Statistical analysis was performed with 4-way ANOVA and, if required, with 3-way ANOVA (α=.05). RESULTS: The mean ±standard deviations ranged from 57.0 ±11.1 MPa to 61.5 ±7.1 MPa after 3 days and from 32.3 ±11.7 MPa to 61.0 ±12.4 MPa after 150 days. The pressure of airborne-particle abrasion and the cleaning method had no significant effect on the TBS (P>.05), whereas the luting resin and artificial aging significantly influenced the TBS (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Assistant Professor, Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, Kiel, Germany. Electronic address: ltuerp@proth.uni-kiel.de.
- Laboratory Assistant, Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, Kiel, Germany.
- Research Associate, Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, Kiel, Germany.
- Professor and Chairman, Department of Prosthodontics, Propaedeutics and Dental Materials, School of Dentistry, Christian-Albrechts University at Kiel, Kiel, Germany.
Zitieren
APA
Türp, L., Lehmann, F., Wille, S., & Kern, M. (2025). Influence of different airborne-particle abrasion pressures, cleaning methods, and artificial aging on zirconia ceramic bonding. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.02.014
Vancouver
Türp L, Lehmann F, Wille S, Kern M. Influence of different airborne-particle abrasion pressures, cleaning methods, and artificial aging on zirconia ceramic bonding. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.02.014
BibTeX
@article{Trp2025,
author = {Türp, Lisa and Lehmann, Frank and Wille, Sebastian and Kern, Matthias},
title = {Influence of different airborne-particle abrasion pressures, cleaning methods, and artificial aging on zirconia ceramic bonding},
journal = {The Journal of Prosthetic Dentistry},
year = {2025},
doi = {10.1016/j.prosdent.2025.02.014}
}
EUVIMED