EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of additive and subtractive zirconia and lithium disilicate manufacturing on tensile bond strength and surface topography

Andreas Kessler, Thilo Reichert, Stefanie Lindner, Anja Liebermann, Moataz El Gezawi, Dalia Kaisarly

The Journal of Prosthetic Dentistry · 2024

DOI: 10.1016/j.prosdent.2024.04.002 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von Andreas Kessler und 5 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Professor, Department of Prosthetic Dentistry, Faculty of Medicine, Center for Dental Medicine, Medical Center - University of Freiburg, Un…. Hauptthemen laut MEDLINE: Zirconium, Tensile Strength, Dental Porcelain, Surface Properties. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Although bonding is important for long-term clinical success, studies on the bonding of additively manufactured ceramics are sparse. PURPOSE: The purpose of this in vitro study was to determine the influence of manufacturing methods, additive (LCM) versus subtractive (CAM). and ceramic materials, zirconia (ZrO2) and lithium disilicate (LiSi), on the tensile bond strength (TBS), failure mode, and surface roughness of ceramics. MATERIAL AND METHODS: A total of 240 ceramic specimens (n=60/group; 2×2×10 mm) were prepared. Two additively manufactured (LCM-printed) ceramics, LiSi and ZrO2 (Lithoz), subtractively manufactured LiSi (IPS e.max CAD), and subtractively manufactured ZrO2 (KATANA Zirconia HTML PLUS) were evaluated. From each material, 40 specimens were bonded together (n=20 ceramic-ceramic specimens/group), and 20 specimens were bonded to equally sized human dentin specimens (n=20 ceramic-dentin specimens/group). The ZrO2 specimens were airborne-particle abraded (Al2O3, 50 µm, 0.1 MPa), and the LiSi specimens were etched with hydrofluoric acid. Then, a universal primer (Monobond Plus) was applied. After the dentin was coated with an etch-and-rinse adhesive (Syntac Classic), the specimens were bonded with luting composite resin (Variolink Esthetic DC), light polymerized for 40 seconds, thermally aged (10 000 cycles between 5 °C and 55 °C), tested for TBS, and statistically analyzed (1- and 3-way ANOVA and Weibull analysis). The ceramic surface was examined with scanning electron microscopy, and surface roughness was measured with digital microscopy before and after surface pretreatment. RESULTS: TBS varied between 5.88 ±2.22 MPa and 6.34 ±2.26 MPa in the ceramic-dentin groups and 12.40 ±1.56 MPa and 18.82 ±5.92 MPa in the ceramic-ceramic groups. No significant difference was observed regarding the manufacturing method and material for different bonding conditions (P>.05). Additive and subtractive LiSi showed the highest reliability with m=18.27. The ceramic-ceramic specimens failed cohesively in the luting composite resin, whereas the ceramic-dentin specimens failed adhesively. CONCLUSIONS: The manufacturing method and material used had little effect on bond strength values or surface properties. The recently introduced printed materials performed similarly to conventionally milled materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumTensile StrengthDental PorcelainSurface PropertiesDental BondingCeramicsMaterials TestingHumansDental Stress AnalysisIn Vitro TechniquesDental MaterialsComputer-Aided DesignResin Cements

Substanzen

Zirconiumlithia disilicateDental Porcelainzirconium oxideDental MaterialsResin Cements

Autor:innen und Institutionen

  • Assistant Professor, Department of Prosthetic Dentistry, Faculty of Medicine, Center for Dental Medicine, Medical Center - University of Freiburg, University of Freiburg, Freiburg, Germany; Assistant Professor, Departme…
  • Postdoctorate, Department of Conservative Dentistry and Periodontology, University Hospital, Ludwig-Maximilian-University of Munich, Munich, Germany.
  • Assistant Professor, Department of Conservative Dentistry and Periodontology, University Hospital, Ludwig-Maximilian-University of Munich, Munich, Germany.
  • Full Professor and Department Head, Department of Prosthetic Dentistry, University Hospital of Cologne, Cologne, Germany.
  • Full Professor, Department of Restorative Dental Sciences, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.

Zitieren

APA

Kessler, A., Reichert, T., Lindner, S., Liebermann, A., El Gezawi, M., & Kaisarly, D. (2024). Influence of additive and subtractive zirconia and lithium disilicate manufacturing on tensile bond strength and surface topography. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.04.002

Vancouver

Kessler A, Reichert T, Lindner S, Liebermann A, El Gezawi M, Kaisarly D. Influence of additive and subtractive zirconia and lithium disilicate manufacturing on tensile bond strength and surface topography. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.04.002

BibTeX
@article{Kessler2024,
  author = {Kessler, Andreas and Reichert, Thilo and Lindner, Stefanie and Liebermann, Anja and El Gezawi, Moataz and Kaisarly, Dalia},
  title = {Influence of additive and subtractive zirconia and lithium disilicate manufacturing on tensile bond strength and surface topography},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  doi = {10.1016/j.prosdent.2024.04.002}
}
Kostenlos starten →