Femtosecond laser versus hydrofluoric acid: Effects on the resin bond strength of CAD/CAM materials
European Journal of Oral Sciences · 2025-12 · 133 (6)
DOI: 10.1111/eos.70038 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift European Journal of Oral Sciences, online erschienen am 30.08.2025. Verfasst von Yener Okutan und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Department of Prosthodontics, Aydın Adnan Menderes University, Aydın, Turkey. Hauptthemen laut MEDLINE: Hydrofluoric Acid, Computer-Aided Design, Dental Bonding, Resin Cements. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 30 Literaturangaben.
Abstract (Originalsprache)
This study evaluated the influence of femtosecond (fs) laser micromachining and hydrofluoric acid (HF)‐etching on the surface roughness (Ra) and resin bond strength of restorative materials. The study used 120 rectangular‐shaped specimens from four computer‐aided design/manufacturing (CAD/CAM) blocks (lithium‐disilicate glass‐ceramic [LDS; e.max CAD], leucite‐reinforced glass‐ceramic [LGC; Empress CAD], zirconia‐reinforced lithium‐silicate [ZLS; Vita Suprinity], and polymer‐infiltrated‐ceramic‐network [PICN; Vita Enamic]) and divided them into three subgroups based on the surface treatments applied: Control, HF‐etching (HF), and fs‐laser irradiation (FS). Surface roughness was measured using a surface profilometer. The surfaces were examined by a scanning electron microscope. A silane bonding agent was applied, and a self‐adhesive dual‐cure resin cement was bonded to the surfaces. The shear bond strength (SBS) test was conducted using a universal test device. FS‐treated groups had higher Ra than HF‐treated specimens. PICN showed higher Ra than other materials among the FS‐treated groups. The HF‐treated LDS showed the highest SBS. ZLS had the lowest SBS among the etched groups. Regardless of the material, the fs‐laser treatment resulted in significantly higher SBS values than seen for controls. Fs‐laser micromachining could be a promising alternative to conventional HF‐etching, given its potential to uniformly roughen the bonding surface of CAD/CAM materials and improve resin bonding.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Faculty of Dentistry, Department of Prosthodontics, Aydın Adnan Menderes University, Aydın, Turkey.
- Private Dental Clinic, Antalya, Turkey.
- Department of Metallurgy and Materials Engineering, Dokuz Eylül University, İzmir, Turkey.
- Department of Computer Technologies, Kadınhanı Faik İçil Vocational High School, Selcuk University, Konya, Turkey.
- Faculty of Dentistry, Department of Prosthodontics, Selcuk University, Konya, Turkey.
ORCID-Profile: Yener Okutan, Banucicek Kandemir, Ipek Bayraktar, Hamdi Sukur Kilic, Yasemin Gundogdu Kabakci, Huseyin Seker, Munir Tolga Yucel
Zitieren
APA
Okutan, Y., Kandemir, B., Bayraktar, I., Kilic, H. S., Kabakci, Y. G., Seker, H., & Yucel, M. T. (2025). Femtosecond laser versus hydrofluoric acid: Effects on the resin bond strength of CAD/CAM materials. European Journal of Oral Sciences, 133(6). https://doi.org/10.1111/eos.70038
Vancouver
Okutan Y, Kandemir B, Bayraktar I, Kilic HS, Kabakci YG, Seker H, et al. Femtosecond laser versus hydrofluoric acid: Effects on the resin bond strength of CAD/CAM materials. European Journal of Oral Sciences. 2025;133(6). doi:10.1111/eos.70038
BibTeX
@article{Okutan2025,
author = {Okutan, Yener and Kandemir, Banucicek and Bayraktar, Ipek and Kilic, Hamdi Sukur and Kabakci, Yasemin Gundogdu and Seker, Huseyin and Yucel, Munir Tolga},
title = {Femtosecond laser versus hydrofluoric acid: Effects on the resin bond strength of CAD/CAM materials},
journal = {European Journal of Oral Sciences},
year = {2025},
volume = {133},
number = {6},
doi = {10.1111/eos.70038}
}
EUVIMED