EUVIMEDEUVIMED entdecken
Crossref

Development of an antimicrobial, 3D printable denture base material with K18 quaternary ammonium silane-functionalized methyl methacrylate and filler

Mansi Patel, Leslie Barrera, Lianrui Chu, Kyumin Whang

The Journal of Prosthetic Dentistry · 2024

DOI: 10.1016/j.prosdent.2024.03.013 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von Mansi Patel und 3 weiteren Autor:innen. Beteiligte Einrichtung: Undergraduate student and Researcher, Department of Comprehensive Dentistry, University of Texas Health Science Center at San Antonio, San Antonio, T…. Hauptthemen laut MEDLINE: Denture Bases, Methylmethacrylate, Silanes, Quaternary Ammonium Compounds. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 37 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Denture base materials are highly susceptible to microbial colonization, which can lead to denture stomatitis. In addition, patients who sleep with their dentures have an increased chance of contracting pneumonia. Commercially available antimicrobial denture base materials to prevent or combat microbial colonization are lacking. PURPOSE: The purpose of this in vitro study was to determine the effects of K18 quaternary ammonium methacryloxy silane-functionalized filler (K18-Filler) and methyl methacrylate (K18-MMA) on the polymerization of 3D printed denture base material and its esthetic, mechanical, and antimicrobial properties. MATERIAL AND METHODS: K18-Filler (0%, 10%, 20% w/w) and K18-MMA (0%, 5%, 12.5% w/w) were added to a 3D printable denture base resin (Denture Base Resin, Original Pink; Formlabs Inc) and 3D printed. Specimens were tested by using the Rockwell15T hardness, near infrared FTIR monomer-to-polymer degree of conversion (DoC), transparency parameter (TP), color shift, and 3-point bend and by counting colony forming units against Streptococcus aureus, Streptococcus sanguinis and Candida albicans tests. Data were analyzed using analysis of variance with the Tukey-Kramer HSD post hoc test. RESULTS: Control resins had significantly higher Rockwell15T hardness than most of the K18 groups (P 8. All K18 groups had comparable or greater moduli than the controls, but the controls had significantly higher ultimate transverse strengths than most K18 groups (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesMethylmethacrylateSilanesQuaternary Ammonium CompoundsPrinting, Three-DimensionalDental MaterialsAnti-Infective AgentsMaterials TestingPolymerizationIn Vitro TechniquesHumansCandida albicans

Substanzen

MethylmethacrylateSilanesQuaternary Ammonium CompoundsDental MaterialsAnti-Infective Agents

Autor:innen und Institutionen

  • Undergraduate student and Researcher, Department of Comprehensive Dentistry, University of Texas Health Science Center at San Antonio, San Antonio, Texas.
  • Research Associate, Department of Comprehensive Dentistry, University of Texas Health Science Center at San Antonio, San Antonio, Texas.
  • Adjunct Faculty Member, Department of Comprehensive Dentistry, University of Texas Health Science Center at San Antonio, San Antonio, Texas.
  • Professor, Department of Comprehensive Dentistry, University of Texas Health Science Center at San Antonio, San Antonio, Texas. Electronic address: whang@uthscsa.edu.

Zitieren

APA

Patel, M., Barrera, L., Chu, L., & Whang, K. (2024). Development of an antimicrobial, 3D printable denture base material with K18 quaternary ammonium silane-functionalized methyl methacrylate and filler. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.03.013

Vancouver

Patel M, Barrera L, Chu L, Whang K. Development of an antimicrobial, 3D printable denture base material with K18 quaternary ammonium silane-functionalized methyl methacrylate and filler. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.03.013

BibTeX
@article{Patel2024,
  author = {Patel, Mansi and Barrera, Leslie and Chu, Lianrui and Whang, Kyumin},
  title = {Development of an antimicrobial, 3D printable denture base material with K18 quaternary ammonium silane-functionalized methyl methacrylate and filler},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  doi = {10.1016/j.prosdent.2024.03.013}
}
Kostenlos starten →