Evaluation of the virtual cement gap parameter of different CAD software programs in designing a single crown restoration: An in vitro study
The Journal of Prosthetic Dentistry · 2023
DOI: 10.1016/j.prosdent.2023.03.010 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023. Verfasst von Moamen Mohsen Sarhan und 3 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Lecturer of Prosthodontics, Faculty of Dentistry, Damanhour University, Damanhour, Egypt; and PhD student, Department of Prosthodontics, Fa…. Hauptthemen laut MEDLINE: Dental Prosthesis Design, Dental Marginal Adaptation. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 38 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: The accuracy of different virtual cement gap parameters in designing a single crown in a computer-aided design (CAD) software program is still unclear. PURPOSE: The purpose of this in vitro study was to evaluate and compare the virtual cement gap settings of 3 different CAD software programs used to design a single crown restoration. MATERIAL AND METHODS: Three different CAD software programs (exocad, Dental System, and B4D) were evaluated for designing single crowns with similar virtual cement gap settings. Three experimental groups were created based on the CAD software program used (n=10). Three-dimensional analysis software program was used to assess the virtual cement gap in the CAD restoration. The Shapiro-Wilk test of normality was used. Comparisons were carried out by using 1-way ANOVA and the Scheffé post hoc test (α=.05). RESULTS: The Dental System software program had the lowest statistical mean error values at both tooth margin (4.6 μm) and axial wall (1.5 μm), followed by B4D then exocad. At the occlusal surface, the lowest statistical mean error value of 5 μm was achieved by the Dental System followed by exocad then B4D. CONCLUSIONS: Accuracy of the virtual cement gap parameter in single crown design varies based on the CAD software used. The highest accuracy was attained by the Dental System software program at all tooth surfaces, followed by B4D at the tooth margin and axial wall and by exocad at the occlusal surface.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Assistant Lecturer of Prosthodontics, Faculty of Dentistry, Damanhour University, Damanhour, Egypt; and PhD student, Department of Prosthodontics, Faculty of Dentistry, Alexandria University, Alexandria, Egypt. Electron…
- Professor and Chairman, Department of Prosthodontics, Faculty of Dentistry, Alexandria University, Alexandria, Egypt.
- Professor of Prosthodontics, Faculty of Dentistry, Alexandria University, Alexandria, Egypt.
Zitieren
APA
Sarhan, M. M., Khamis, M. M., Abdelhamid, A. M., & Ezzelarab, S. (2023). Evaluation of the virtual cement gap parameter of different CAD software programs in designing a single crown restoration: An in vitro study. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2023.03.010
Vancouver
Sarhan MM, Khamis MM, Abdelhamid AM, Ezzelarab S. Evaluation of the virtual cement gap parameter of different CAD software programs in designing a single crown restoration: An in vitro study. The Journal of Prosthetic Dentistry. 2023. doi:10.1016/j.prosdent.2023.03.010
BibTeX
@article{Sarhan2023,
author = {Sarhan, Moamen Mohsen and Khamis, Mohamed Moataz and Abdelhamid, Ahmed Mohamed and Ezzelarab, Salah},
title = {Evaluation of the virtual cement gap parameter of different CAD software programs in designing a single crown restoration: An in vitro study},
journal = {The Journal of Prosthetic Dentistry},
year = {2023},
doi = {10.1016/j.prosdent.2023.03.010}
}
EUVIMED