Shear bond strength of porcelain to milled and stereolithography additively manufactured zirconia with and without surface treatment: An in vitro study
The Journal of Prosthetic Dentistry · 2025
DOI: 10.1016/j.prosdent.2023.02.007 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Amirali Zandinejad und 5 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Comprehensive Dentistry, College of Dentistry, Texas A&M University, Dallas, Texas; Private practice, Arlington, T…. Hauptthemen laut MEDLINE: Zirconium, Dental Porcelain, Dental Bonding. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 62 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Delamination of veneering ceramic is one of the most common challenges relating to veneered zirconia restorations. Additive manufacturing (AM) is a fast-expanding technology that has gained widespread acceptance in dentistry and is increasingly being used to produce dental restorations. However, information about bonding of porcelain to AM zirconia is lacking. PURPOSE: The purpose of this in vitro study was to investigate the shear bond strength (SBS) of porcelain to milled and additively manufactured zirconia, and the effect of surface treatment on bond strength. MATERIAL AND METHODS: A Ø12×5-mm disk was designed virtually to fabricate all specimens, which were divided into 2 groups according to the manufacturing technique: additively manufactured or milled zirconia. The effect of airborne-particle abrasion and a zirconia liner before porcelain application was investigated in both groups. Veneering porcelain was fired into an alumina ring mold on the zirconia surface. SBS was measured by using a universal testing machine at a crosshead speed of 1 mm/min before and after aging (n=10). SBS data were analyzed with 3-way ANOVA (α=.05) RESULTS: A significant difference was found between milled and AM zirconia. The SBS of porcelain to milled zirconia was significantly higher (1.38 MPa) than to AM zirconia (0.68 MPa) (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Associate Professor, Department of Comprehensive Dentistry, College of Dentistry, Texas A&M University, Dallas, Texas; Private practice, Arlington, Texas. Electronic address: azandinejad70@gmail.com.
- Lecturer, AEGD Residency Program, Department of Comprehensive Dentistry, College of Dentistry, Texas A&M University, Dallas, Texas.
- Assistant Professor, Clinical Research and Biostatistics, Department of Comprehensive Dentistry, EIOH Medical Center, University of Rochester, Rochester, NY.
- Senior Lecturer, Oral Prosthetic Engineering, Graduate School, Tokyo Medical and Dental University, Tokyo, Japan.
- Professor, Department of Cariology and Operative Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University, Tokyo, Japan.
- Professor and Division Head, Division of Prosthodontics, School of Dentistry, University of Maryland, Baltimore, MD.
Zitieren
APA
Zandinejad, A., Khanlar, L. N., Barmak, A. B., Ikeda, M., Tagami, J., & Masri, R. (2025). Shear bond strength of porcelain to milled and stereolithography additively manufactured zirconia with and without surface treatment: An in vitro study. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2023.02.007
Vancouver
Zandinejad A, Khanlar LN, Barmak AB, Ikeda M, Tagami J, Masri R. Shear bond strength of porcelain to milled and stereolithography additively manufactured zirconia with and without surface treatment: An in vitro study. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2023.02.007
BibTeX
@article{Zandinejad2025,
author = {Zandinejad, Amirali and Khanlar, Leila Nasiry and Barmak, Abdul Basir and Ikeda, Masaomi and Tagami, Junji and Masri, Radi},
title = {Shear bond strength of porcelain to milled and stereolithography additively manufactured zirconia with and without surface treatment: An in vitro study},
journal = {The Journal of Prosthetic Dentistry},
year = {2025},
doi = {10.1016/j.prosdent.2023.02.007}
}
EUVIMED