EUVIMEDEUVIMED entdecken
Crossref

Fracture load of 4-unit interim fixed partial dentures using 3D-printed and traditionally manufactured materials

Andreas Greuling, Annika Matthies, Michael Eisenburger

The Journal of Prosthetic Dentistry · 2023-04 · 129 (4) · 607.e1-607.e8

DOI: 10.1016/j.prosdent.2022.12.013 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023-04. Verfasst von Andreas Greuling und 2 weiteren Autor:innen. Beteiligte Einrichtung: Head of Materials Science Lab, Department of Prosthetic Dentistry and Biomedical Materials Science, Hannover Medical School, Hannover, Germany. Elect…. Hauptthemen laut MEDLINE: Dental Restoration Failure, Dental Materials. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 32 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: How the fracture strength of recently introduced 3-dimensionally (3D) printed interim materials compares with that of conventional materials is unclear. PURPOSE: The purpose of this in vitro study was to compare the fracture load of 4-unit interim fixed partial dentures made from 3 different materials before and after mastication simulation. MATERIAL AND METHODS: Based on a master model of a 4-unit fixed partial denture with maxillary left first premolar and second molar abutment teeth, interim restorations were fabricated from 3 different materials (3D-printed, Temporary CB Resin, milled, PMMA for brain, and manually manufactured, Luxatemp Plus). The fixed partial dentures (n=30 for each material) were cemented on 3D-printed model abutment teeth that were connected via a thin latex layer to a polyurethane base block. The fracture load of 15 fixed partial dentures of each material was tested without aging. Another 15 fixed partial dentures of each material were tested after thermomechanical aging. RESULTS: The mean fracture load was between 186 N and 661 N, and all materials showed significant lower fracture loads after aging. Before and after aging (before/after ±standard deviation) milled (661 ±59/568 ±52 N) achieved the highest loads before manually manufactured (621 ±100/478 ±96 N) and 3D-printed (294 ±83/186 ±70). CONCLUSIONS: The 3D-printed interim restoration material and the inherent manufacturing process show significant lower fracture loads than the tested alternatives. However, as the influence of geometric differences could not be quantified, whether this remains true after correcting for geometric differences remains unclear. For the tested interim materials, thermocycling and mastication simulation significantly reduced fracture loads over time, even at loads as low as 50 N.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental Restoration FailureDental MaterialsMaterials TestingPrinting, Three-DimensionalDenture, Partial, Fixed

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Head of Materials Science Lab, Department of Prosthetic Dentistry and Biomedical Materials Science, Hannover Medical School, Hannover, Germany. Electronic address: Greuling.Andreas@mh-hannover.de.
  • Doctoral candidate, Department of Prosthetic Dentistry and Biomedical Materials Science, Hannover Medical School, Hannover, Germany.
  • Professor, Department of Prosthetic Dentistry and Biomedical Materials Science, Hannover Medical School, Hannover, Germany.

Zitieren

APA

Greuling, A., Matthies, A., & Eisenburger, M. (2023). Fracture load of 4-unit interim fixed partial dentures using 3D-printed and traditionally manufactured materials. The Journal of Prosthetic Dentistry, 129(4), 607.e1-607.e8. https://doi.org/10.1016/j.prosdent.2022.12.013

Vancouver

Greuling A, Matthies A, Eisenburger M. Fracture load of 4-unit interim fixed partial dentures using 3D-printed and traditionally manufactured materials. The Journal of Prosthetic Dentistry. 2023;129(4):607.e1-607.e8. doi:10.1016/j.prosdent.2022.12.013

BibTeX
@article{Greuling2023,
  author = {Greuling, Andreas and Matthies, Annika and Eisenburger, Michael},
  title = {Fracture load of 4-unit interim fixed partial dentures using 3D-printed and traditionally manufactured materials},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2023},
  volume = {129},
  number = {4},
  pages = {607.e1--607.e8},
  doi = {10.1016/j.prosdent.2022.12.013}
}
Kostenlos starten →