Effect of different additive manufacturing technologies on the fracture load of 3-unit monolithic zirconia fixed partial dentures: In vitro mechanical evaluation and energy-dispersive spectroscopy analysis
The Journal of Prosthetic Dentistry · 2025
DOI: 10.1016/j.prosdent.2025.03.015 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Simge Dagistan und 3 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Bahcesehir University, Istanbul, Turkey. Electronic address: simge_baytur@ho…. Hauptthemen laut MEDLINE: Zirconium, Denture, Partial, Fixed, Denture Design, Dental Materials. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 40 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Studies examining the influence of different fabrication techniques on the fracture load (FL) of monolithic zirconia restorations are sparse. PURPOSE: The purpose of this in vitro study was to compare the FL of monolithic zirconia restorations manufactured with different technologies. MATERIAL AND METHODS: A typodont model with a missing left first molar was used and laboratory scanned (inEos X5; Dentsply Sirona). Data were transferred to a computer-aided design software program (InLab 16.1; Dentsply Sirona). The cement space for the 3-unit fixed partial dentures was set at 50 µm, and the connector area was specified as 9 ±0.2 mm2. The subtractive technique was designated as the control group (GC Initial Zirconia HT; GC Corp), while 3 experimental groups were created by using different additive techniques (GrSLA [3DMix Zirconia 3Y; 3D Ceram], GrDLP [Inni Cera; Aon], and GrLCM [LithaCon 3Y 210; Lithoz]) (n=8). In all groups, 3 mol% yttria-stabilized tetragonal zirconia polycrystalline was used. The FL test was conducted on models fabricated from glass-filled resin-based methacrylate and postpolymerized. After thermal cycling (5000 cycles, 5-55 °C), all specimens were loaded with a stainless-steel ball at a crosshead speed of 1 mm/minute until fracture in a precision universal testing device. The maximum loads at fracture were recorded in N. Weibull analysis was used to determine the characteristic strength and reliability. The fracture lines were analyzed by scanning electron microscopy at magnifications of ×50 and ×500. The elemental compositions were compared with energy dispersive spectroscopy. A 1-way ANOVA and Tukey post hoc test were used for statistical analysis (α=.05). RESULTS: Significant differences in FL values were found among the groups (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Bahcesehir University, Istanbul, Turkey. Electronic address: simge_baytur@hotmail.com.
- Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Near East University, Nicosia, North Cyprus.
- Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Near East University, Nicosia, North Cyprus.
- Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey.
Zitieren
APA
Dagistan, S., Toksoy, D., Önöral, Ö., & Diken Turksayar, A. A. (2025). Effect of different additive manufacturing technologies on the fracture load of 3-unit monolithic zirconia fixed partial dentures: In vitro mechanical evaluation and energy-dispersive spectroscopy analysis. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.03.015
Vancouver
Dagistan S, Toksoy D, Önöral Ö, Diken Turksayar AA. Effect of different additive manufacturing technologies on the fracture load of 3-unit monolithic zirconia fixed partial dentures: In vitro mechanical evaluation and energy-dispersive spectroscopy analysis. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.03.015
BibTeX
@article{Dagistan2025,
author = {Dagistan, Simge and Toksoy, Dilem and Önöral, Özay and Diken Turksayar, Almira Ada},
title = {Effect of different additive manufacturing technologies on the fracture load of 3-unit monolithic zirconia fixed partial dentures: In vitro mechanical evaluation and energy-dispersive spectroscopy analysis},
journal = {The Journal of Prosthetic Dentistry},
year = {2025},
doi = {10.1016/j.prosdent.2025.03.015}
}
EUVIMED