EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

A feasibility study of 3D printing technology for simulating rigid gas permeable contact lens fitting

Nerea Tolón Zardoya, Diana Gargallo Yebra, Francisco J Ávila Gómez, Jorge Ares García

Journal of Optometry · 2026

DOI: 10.1016/j.optom.2025.100583 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Optometry, 2026. Verfasst von Nerea Tolón Zardoya und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Applied physics, University of Zaragoza, Pedro Cerbuna, 12, 50009 Zaragoza Spain. Electronic address: 684216@unizar.es. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Contact Lenses, Prosthesis Fitting. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Spain Ministry of Science and Innovation, Gobierno de Aragón.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: To assess the feasibility of a novel method for simulating a Rigid Gas Permeable Contact Lenses (RGP-CL) fitting using 3-D printed sclero-corneal surfaces (SCSs). METHODS: The experiment involved the fabrication of two resin SCSs with biconic corneal geometry and the participation of 22 optician-optometrists as observers. Participants compared the fluorescein patterns of three RGP-CL fitted on each SCS with theoretical patterns generated through computer simulation. To standardize visualization, comparisons were conducted through a multiple-choice questionnaire composed of 6 questions. Each question presented one main fluorescein pattern (either theoretical or experimental) and four additional patterns obtained using the other technique. Optometrists were required to select the fluorescein pattern more similar to the main pattern. A statistical analysis was performed to evaluate the accuracy of the comparison between the two methods. RESULTS: The surface quality of the printed SCSs was sufficient to produce consistent and interpretable fluorescein patterns. In all questions, at least 70 % of optometrists selected the correct pattern. In four questions, more than 90 % identified the correct pattern, and in one question accuracy reached 100 %. The correct option was always the most frequently chosen, with a significantly higher rate than the second most selected option (p = 0.05). CONCLUSIONS: The ability of most optometrists to correctly identify patterns suggests that, even without polishing, 3-D printed SCSs can simulate fluorescein patterns closely resembling theoretical ones. This approach shows promise as a supportive tool for training in RGP-CL fitting.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalContact LensesProsthesis FittingHumansFeasibility StudiesCorneaComputer SimulationFluoresceinSclera

Stichwörter der Autor:innen

3D-printingContact lens fittingFluorescein patternRGP contact lens

Substanzen

Fluorescein

Autor:innen und Institutionen

  • Department of Applied physics, University of Zaragoza, Pedro Cerbuna, 12, 50009 Zaragoza Spain. Electronic address: 684216@unizar.es.
  • Department of Applied physics, University of Zaragoza, Pedro Cerbuna, 12, 50009 Zaragoza Spain. Electronic address: dgargallo@unizar.es.
  • Department of Applied physics, University of Zaragoza, Pedro Cerbuna, 12, 50009 Zaragoza Spain. Electronic address: avila@unizar.es.
  • Department of Applied physics, University of Zaragoza, Pedro Cerbuna, 12, 50009 Zaragoza Spain. Electronic address: fatxutxa@unizar.es.

Förderung

  • Spain Ministry of Science and Innovation
  • Gobierno de Aragón

Zitieren

APA

Tolón Zardoya, N., Gargallo Yebra, D., Ávila Gómez, F. J., & Ares García, J. (2026). A feasibility study of 3D printing technology for simulating rigid gas permeable contact lens fitting. Journal of Optometry. https://doi.org/10.1016/j.optom.2025.100583

Vancouver

Tolón Zardoya N, Gargallo Yebra D, Ávila Gómez FJ, Ares García J. A feasibility study of 3D printing technology for simulating rigid gas permeable contact lens fitting. Journal of Optometry. 2026. doi:10.1016/j.optom.2025.100583

BibTeX
@article{TolnZardoya2026,
  author = {Tolón Zardoya, Nerea and Gargallo Yebra, Diana and Ávila Gómez, Francisco J and Ares García, Jorge},
  title = {A feasibility study of 3D printing technology for simulating rigid gas permeable contact lens fitting},
  journal = {Journal of Optometry},
  year = {2026},
  doi = {10.1016/j.optom.2025.100583}
}
Kostenlos starten →