Effect of welding parameters on microstructure and mechanical properties of GMAW welded S275 steel welded zone
Discover Materials · 19.12.2024 · 4 (1)
DOI: 10.1007/s43939-024-00169-4 ↗Kurz gefasst
Fachartikel in der Zeitschrift Discover Materials, online erschienen am 19.12.2024. Verfasst von Muhammad Shafeek und 3 weiteren Autor:innen. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
This study investigates the effect of welding parameters on the microstructural evolution and mechanical properties, such as tensile strength and hardness, in mild steel plates welded using gas metal arc welding (GMAW). The welding parameters examined include welding current, arc voltage, and gas flow rate, with ER K-71 T filler wire as the consumable material. Results indicate that a higher welding current and reduced gas flow rate result in a maximum tensile strength of approximately 533 MPa. However, discrepancies were noted in the microhardness data across different zones, with the heat-affected zone (HAZ) exhibiting a hardness of 115.8 HV, while the weld zone and base metal showed values of 76.7 HV and 112.9 HV, respectively. Microstructural analysis revealed the presence of bainite and ferrite with a tempered martensitic structure in the welded area, demonstrating that the combination of welding parameters plays a critical role in controlling phase transformations and mechanical behavior. It is essential to reconcile the observed hardness values with the conclusions drawn to ensure accurate interpretation of the data. The study investigates how different welding process parameters, including current, voltage, and gas flow, affect the internal structure and mechanical characteristics of weld metal. It was found that the highest tensile strength is achieved with a combination of high welding current and low gas flow rate. The welded joint shows greater hardness in the heat-affected zone compared to the original metal, with the fusion zone being less hard. Analysis of the weld area reveals the presence of bainite, ferrite, and tempered martensite, which are responsible for the mechanical properties observed. The study investigates how different welding process parameters, including current, voltage, and gas flow, affect the internal structure and mechanical characteristics of weld metal. It was found that the highest tensile strength is achieved with a combination of high welding current and low gas flow rate. The welded joint shows greater hardness in the heat-affected zone compared to the original metal, with the fusion zone being less hard. Analysis of the weld area reveals the presence of bainite, ferrite, and tempered martensite, which are responsible for the mechanical properties observed.
Zitieren
APA
Shafeek, M., Suranjan, S., Doreswamy, D., & Sachidananda, H. K. (2024). Effect of welding parameters on microstructure and mechanical properties of GMAW welded S275 steel welded zone. Discover Materials, 4(1). https://doi.org/10.1007/s43939-024-00169-4
Vancouver
Shafeek M, Suranjan S, Doreswamy D, Sachidananda HK. Effect of welding parameters on microstructure and mechanical properties of GMAW welded S275 steel welded zone. Discover Materials. 2024;4(1). doi:10.1007/s43939-024-00169-4
BibTeX
@article{Shafeek2024,
author = {Shafeek, Muhammad and Suranjan, Sampath and Doreswamy, Deepak and Sachidananda, H. K.},
title = {Effect of welding parameters on microstructure and mechanical properties of GMAW welded S275 steel welded zone},
journal = {Discover Materials},
year = {2024},
volume = {4},
number = {1},
doi = {10.1007/s43939-024-00169-4}
}
EUVIMED