EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Cladding of Carbon Steel with Stainless Steel Using Friction Stir Welding: Effect of Process Parameters on Microstructure and Mechanical Properties

Mahmoud S. I. Ahmed, Mohamed M. Z. Ahmed, Hussein M. Abd El-Aziz, Mohamed I. A. Habba, Ashraf F. Ismael, Mohamed M. El-Sayed Seleman, Ali Abd El-Aty, Ali Alamry, Bandar Alzahrani, Kamel Touileb, Wael M. Fathy

Crystals · 01.11.2023 · 13 (11) · 1559

DOI: 10.3390/cryst13111559 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 01.11.2023. Verfasst von Mahmoud S. I. Ahmed und 10 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Prince Sattam Bin Abdulaziz University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of this study is to investigate friction stir welding (FSW) to join A304 austenitic stainless steel and low carbon steel A283 Gr. C in-lap configuration to clad the carbon steel with highly corrosion-resistant stainless steel. Thus, a wide range of FSW parameters were investigated such as FSW tool rotation rate from 200 to 400 rpm, tool traverse speed from 25 to 75 mm/min, and vertical forces of 20 to 32 KN. The FSW parameters combination of high welding rotation rate (400 rpm) and high vertical forces (32 KN) results in rejected joints in terms of surface appearance and clear surface defects. On the other hand, rotation rates of 200 and 300 rpm with different welding speeds and vertical forces resulted in some sound joints that were further investigated for microstructure and mechanical properties. The sound lap joints were examined via optical microstructure, SEM, and EDS investigations. For the mechanical properties, both tensile shear testing and hardness testing were used. The transverse macrographs showed intermixing between the two dissimilar materials with an almost irregular interface. The hardness profile in both materials showed a significant increase across the different regions from the Base Material (BM) to the nugget zone, with a maximum value of 260 Hv in the stainless steel and 245 Hv in the carbon steel. This increase is mainly attributed to the grain refining in the weld region due to the dynamic recrystallization and transformations upon the thermomechanical cycle. The tensile shear load of the joints varied from 20 to 27 KN for the FSWed joints, with the highest joint tensile shear load of 27 KN for that produced at 300 rpm tool rotation and 25 mm/min welding speed.

Förderung

  • Prince Sattam Bin Abdulaziz University

Zitieren

APA

Ahmed, M. S. I., Ahmed, M. M. Z., El-Aziz, H. M. A., Habba, M. I. A., Ismael, A. F., Seleman, M. M. E., El-Aty, A. A., Alamry, A., Alzahrani, B., Touileb, K., & Fathy, W. M. (2023). Cladding of Carbon Steel with Stainless Steel Using Friction Stir Welding: Effect of Process Parameters on Microstructure and Mechanical Properties. Crystals, 13(11), 1559. https://doi.org/10.3390/cryst13111559

Vancouver

Ahmed MSI, Ahmed MMZ, El-Aziz HMA, Habba MIA, Ismael AF, Seleman MME, et al. Cladding of Carbon Steel with Stainless Steel Using Friction Stir Welding: Effect of Process Parameters on Microstructure and Mechanical Properties. Crystals. 2023;13(11):1559. doi:10.3390/cryst13111559

BibTeX
@article{Ahmed2023,
  author = {Ahmed, Mahmoud S. I. and Ahmed, Mohamed M. Z. and El-Aziz, Hussein M. Abd and Habba, Mohamed I. A. and Ismael, Ashraf F. and Seleman, Mohamed M. El-Sayed and El-Aty, Ali Abd and Alamry, Ali and Alzahrani, Bandar and Touileb, Kamel and Fathy, Wael M.},
  title = {Cladding of Carbon Steel with Stainless Steel Using Friction Stir Welding: Effect of Process Parameters on Microstructure and Mechanical Properties},
  journal = {Crystals},
  year = {2023},
  volume = {13},
  number = {11},
  pages = {1559},
  doi = {10.3390/cryst13111559}
}
Kostenlos starten →