EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Single-step aerosol printing of metallic nanostructures via in-flight plasma reduction

Srikanthan Ramesh, Md Shihab Shakur, Chaitanya Mahajan

Progress in Additive Manufacturing · 2026-10 · 11 (10) · 10705-10725

DOI: 10.1007/s40964-026-01921-3 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Progress in Additive Manufacturing, online erschienen am 24.08.2026. Verfasst von Srikanthan Ramesh und 2 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Oklahoma Space Grant Consortium, National Science Foundation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Direct printing of metallic inks rarely achieves functional conductivity in a single step. Most techniques require post-processing, including solvent removal and particle sintering, which restrict applicability in power-limited systems, heat-sensitive substrates, and rapid fabrication scenarios. In this work, we present a plasma-assisted aerosol printing process that integrates deposition and post-processing into a single step. Using this approach, we demonstrate direct metallization of nickel and copper films using formate-ethylenediamine-based metal organic decomposition (MOD) inks at relatively low temperatures. We further demonstrate that co-printing of precursor inks can produce biphasic alloyed films. Increasing the plasma voltage improves in-flight precursor reduction and lowers the resulting film resistivity. The carrier-gas flow rate controls droplet delivery to the plasma reactive zone and, in turn, film uniformity. The solvent composition sets droplet volatility, which determines whether droplets arrive at the substrate dry and fully reduced or wet and only partially reduced. Layer count controls the transition from continuous conductive films at two passes to hierarchically rough, high-surface-area morphologies at higher counts. The process yields resistivities of 273 μΩ·cm for nickel and 14.4 μΩ·cm for copper, comparable to or lower than values reported for other direct-write techniques. Co-printing of the two inks yields a biphasic film in which discrete metallic Ni is dispersed within a Cu-rich (Cu0.95Ni0.05) solid solution. The process-structure relationships established in this work provide a framework for enabling rapid metallization in applications such as space manufacturing, printed electronics, and biocompatible coatings on heat-sensitive substrates.

Förderung

  • Oklahoma Space Grant Consortium
  • National Science Foundation

Zitieren

APA

Ramesh, S., Shakur, M. S., & Mahajan, C. (2026). Single-step aerosol printing of metallic nanostructures via in-flight plasma reduction. Progress in Additive Manufacturing, 11(10), 10705-10725. https://doi.org/10.1007/s40964-026-01921-3

Vancouver

Ramesh S, Shakur MS, Mahajan C. Single-step aerosol printing of metallic nanostructures via in-flight plasma reduction. Progress in Additive Manufacturing. 2026;11(10):10705-10725. doi:10.1007/s40964-026-01921-3

BibTeX
@article{Ramesh2026,
  author = {Ramesh, Srikanthan and Shakur, Md Shihab and Mahajan, Chaitanya},
  title = {Single-step aerosol printing of metallic nanostructures via in-flight plasma reduction},
  journal = {Progress in Additive Manufacturing},
  year = {2026},
  volume = {11},
  number = {10},
  pages = {10705--10725},
  doi = {10.1007/s40964-026-01921-3}
}
Kostenlos starten →