EUVIMEDEUVIMED entdecken
Crossref

Effect of different onlay materials and resin core thickness on stress distribution in partial coverage restorations: a 3D finite element study

Sensen Chen, Yao Chen, Sifan Chen, Changan Chen, Jie Lin

Clinical Oral Investigations · 2026

DOI: 10.1007/s00784-026-07112-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Oral Investigations, 2026. Verfasst von Sensen Chen und 4 weiteren Autor:innen. Beteiligte Einrichtung: Clinical Research Center for Oral Tissue Deficiency Diseases of Fujian Province & Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineer…. Hauptthemen laut MEDLINE: Finite Element Analysis, Inlays, Dental Materials. Die Arbeit nennt 37 Literaturangaben. Gefördert von: Joint Funds for the innovation of science and Technology, Fujian province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

OBJECTIVE: To investigate the effects of onlay materials and resin core thickness on stress distribution in partial coverage restorations under static and thermal loading using finite element analysis (FEA). METHODS: A 3D mandibular first molar model was created from CBCT data. Four materials (zirconia, lithium disilicate [LD], polymer-infiltrated ceramic network [PICN], gold alloy [GA]) and five resin core thicknesses (1 mm to 4 mm, plus full crown control) were tested. A total of 20 models were loaded with 100 N occlusal force and thermal stresses (5-37 °C and 37-55 °C). The distribution characteristics of the maximum principal stress (MPS) were analyzed for different combinations of variables. RESULTS: Under mechanical loading, thin resin cores (1-2 mm) performed best. Increasing thickness to 3 mm sharply raised enamel stress (zirconia: 77.35-80.72 MPa); at 4 mm, restoration stress peaked (zirconia: 150.12 MPa). Zirconia showed highest restoration stress (54.01-150.12 MPa) but lowest dentin stress (5.02-7.70 MPa); PICN had low and most stable restoration stress (55-91 MPa) but highest dentin stress (8-13 MPa). Under high-temperature thermal stress, enamel stress jumped sharply at ≥ 3 mm resin thickness, markedly higher than under low-temperature stress. GA with an extremely thin resin core (1R4O) caused abnormally high dentin stress (50.83 MPa) at low temperature. CONCLUSION: A thin resin core (1-2 mm) offered better overall mechanical performance. Material type markedly influenced stress distribution. High-temperature thermal stress posed a greater threat to tooth structure than low-temperature stress. Thermal stress barely affected periapical/periodontal tissues. CLINICAL RELEVANCE: For extensive MOD restorations, a 2 mm resin core is recommended as the safe threshold. Material selection should balance the protection of the restoration itself and the stress transfer to the tooth structure.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Finite Element AnalysisInlaysDental MaterialsDental Stress AnalysisMaterials TestingZirconiumHumansImaging, Three-DimensionalCeramicsStress, MechanicalDental Porcelain

Stichwörter der Autor:innen

Finite element analysisMaximum principal stressPartial coverage restorationResin coreThermal stress

Substanzen

Zirconiumzirconium oxideDental MaterialsDental Porcelainlithia disilicate

Autor:innen und Institutionen

  • Clinical Research Center for Oral Tissue Deficiency Diseases of Fujian Province & Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineering Research Center of Oral Biomaterial, School and Hospital of Stomat…
  • Stomatological Key Laboratory of Fujian College and University, Institute of oral homeostasis, Department of VIP Dental Service, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, China.
  • Stomatological Key Laboratory of Fujian College and University, Institute of oral homeostasis, Department of VIP Dental Service, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, China. linjie.dds@g…
  • Department of Crown and Bridge, School of Life Dentistry at Tokyo, The Nippon Dental University, 1-9-20 Fujimi, Chiyoda-ku, Tokyo, 102-8159, Japan. linjie.dds@gmail.com.
  • Applied Oral Sciences and Community Dental Care, Faculty of Dentistry, Prince Philip Dental Hospital, University of Hong Kong, 34 Hospital Road, Sai Ying Pun, Hong Kong, China. linjie.dds@gmail.com.

Förderung

  • Joint Funds for the innovation of science and Technology, Fujian province

Zitieren

APA

Chen, S., Chen, Y., Chen, S., Chen, C., & Lin, J. (2026). Effect of different onlay materials and resin core thickness on stress distribution in partial coverage restorations: a 3D finite element study. Clinical Oral Investigations. https://doi.org/10.1007/s00784-026-07112-2

Vancouver

Chen S, Chen Y, Chen S, Chen C, Lin J. Effect of different onlay materials and resin core thickness on stress distribution in partial coverage restorations: a 3D finite element study. Clinical Oral Investigations. 2026. doi:10.1007/s00784-026-07112-2

BibTeX
@article{Chen2026,
  author = {Chen, Sensen and Chen, Yao and Chen, Sifan and Chen, Changan and Lin, Jie},
  title = {Effect of different onlay materials and resin core thickness on stress distribution in partial coverage restorations: a 3D finite element study},
  journal = {Clinical Oral Investigations},
  year = {2026},
  doi = {10.1007/s00784-026-07112-2}
}
Kostenlos starten →