EUVIMEDEUVIMED entdecken
Crossref

Low-cost, tape-sealed, PDMS-molded devices using 3D printing for cell adhesion under flow

Abigail F Kreznor, Stefan H Bossmann, Christopher T Culbertson

Analytical and Bioanalytical Chemistry · 2026

DOI: 10.1007/s00216-026-06360-1 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Analytical and Bioanalytical Chemistry, 2026. Verfasst von Abigail F Kreznor und 2 weiteren Autor:innen. Beteiligte Einrichtung: Kansas State University, Department of Chemistry, Manhattan, KS, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Dimethylpolysiloxanes, Cell Adhesion, Microfluidic Analytical Techniques. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 23 Literaturangaben. Gefördert von: Johnson Cancer Research Center, Kansas State University, National Science Foundation, NCI NIH HHS.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Microfluidics offer a useful platform for cell studies by coupling enhanced fluidic control with real-time imaging, but traditional fabrication methods require expensive equipment and advanced training. In this work, the fabrication and implementation of a low-cost and simple-to-use microfluidic device for cell studies were completed using digital light processing resin 3D printing to produce molds for polydimethylsiloxane (PDMS) devices. Contact angle analysis assessed surface characteristics during fabrication. Tape was used to reversibly seal devices, permitting reuse without damage or adhesion loss. Additionally, tape-sealed devices could withstand an excess of 4 times the internal pressure compared to PDMS devices reversibly sealed on glass. A treatment solution was developed to enable adherent culture of U-87 human glioblastoma cells on the adhesive surface and was confirmed via fluorescence-based viability and morphology monitoring. A miniature incubator, programmable fluidic system, and heating pad were incorporated to maintain conditions for long-term experiments and continuous flow. By employing this unique fabrication method, design prototyping and performance optimization can be rapidly completed for bioanalytical applications of microfluidic-based cell studies. This work provides a foundation, especially for those unfamiliar with microfluidics, to develop microfluidic platforms for cellular analysis using an accessible and less expensive approach.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDimethylpolysiloxanesCell AdhesionMicrofluidic Analytical TechniquesLab-On-A-Chip DevicesHumansCell Line, TumorEquipment Design

Stichwörter der Autor:innen

3D printingCellular adhesionMicrofluidicPDMS

Substanzen

Dimethylpolysiloxanesbaysilon

Autor:innen und Institutionen

  • Kansas State University, Department of Chemistry, Manhattan, KS, USA.
  • The University of Kansas Medical Center, Department of Cancer Biology, Kansas City, KS, USA.
  • Kansas State University, Department of Chemistry, Manhattan, KS, USA. culbert@ksu.edu.

Förderung

  • Johnson Cancer Research Center, Kansas State University
  • National Science Foundation
  • NCI NIH HHS
  • National Cancer Institute

Zitieren

APA

Kreznor, A. F., Bossmann, S. H., & Culbertson, C. T. (2026). Low-cost, tape-sealed, PDMS-molded devices using 3D printing for cell adhesion under flow. Analytical and Bioanalytical Chemistry. https://doi.org/10.1007/s00216-026-06360-1

Vancouver

Kreznor AF, Bossmann SH, Culbertson CT. Low-cost, tape-sealed, PDMS-molded devices using 3D printing for cell adhesion under flow. Analytical and Bioanalytical Chemistry. 2026. doi:10.1007/s00216-026-06360-1

BibTeX
@article{Kreznor2026,
  author = {Kreznor, Abigail F and Bossmann, Stefan H and Culbertson, Christopher T},
  title = {Low-cost, tape-sealed, PDMS-molded devices using 3D printing for cell adhesion under flow},
  journal = {Analytical and Bioanalytical Chemistry},
  year = {2026},
  doi = {10.1007/s00216-026-06360-1}
}
Kostenlos starten →