EUVIMEDEUVIMED entdecken
Open Access

Aerosol Jet Printing Conductive 3D Microstructures from Graphene Without Post‐Processing

Brittany N Smith iD, Peter Ballentine, James L Doherty iD, Ryan Wence, Hansel Alex Hobbie, Nicholas X Williams iD, Aaron D Franklin iD

Small · 2024-03 · 20 (12)

DOI: 10.1002/smll.202305170 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small, online erschienen am 09.11.2023. Verfasst von Brittany N Smith und 6 weiteren Autor:innen. Beteiligte Einrichtung: Electrical and Computer Engineering Department, Duke University, Durham, NC, 27708, USA. Die Arbeit wurde bisher 28-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NHLBI NIH HHS, NIH HHS, National Nanotechnology Coordinating Office.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Three‐dimensional (3D) graphene microstructures have the potential to boost performance in high‐capacity batteries and ultrasensitive sensors. Numerous techniques have been developed to create such structures; however, the methods typically rely on structural supports, and/or lengthy post‐print processing, increasing cost and complexity. Additive manufacturing techniques, such as printing, show promise in overcoming these challenges. This study employs aerosol jet printing for creating 3D graphene microstructures using water as the only solvent and without any post‐print processing required. The graphene pillars exhibit conductivity immediately after printing, requiring no high‐temperature annealing. Furthermore, these pillars are successfully printed in freestanding configurations at angles below 45° relative to the substrate, showcasing their adaptability for tailored applications. When graphene pillars are added to humidity sensors, the additional surface area does not yield a corresponding increase in sensor performance. However, graphene trusses, which add a parallel conduction path to the sensing surface, are found to improve sensitivity nearly 2×, highlighting the advantages of a topologically suspended circuit construction when adding 3D microstructures to sensing electrodes. Overall, incorporating 3D graphene microstructures to sensor electrodes can provide added sensitivity, and aerosol jet printing is a viable path to realizing these conductive microstructures without any post‐print processing.

Schlagwörter

Stichwörter der Autor:innen

3D graphene3D printingadditive manufacturingaerosol jet printinggraphenehumidity sensorsprinted microstructuresrecyclable electronics

Autor:innen und Institutionen

  • Electrical and Computer Engineering Department, Duke University, Durham, NC, 27708, USA.
  • Chemistry Department, Duke University, Durham, NC, 27708, USA.

ORCID-Profile: Brittany N Smith, James L Doherty, Nicholas X Williams, Aaron D Franklin

Förderung

  • NHLBI NIH HHS
  • NIH HHS
  • National Nanotechnology Coordinating Office
  • National Institutes of Health
  • National Science Foundation

Zitieren

APA

Smith, B. N., Ballentine, P., Doherty, J. L., Wence, R., Hobbie, H. A., Williams, N. X., & Franklin, A. D. (2024). Aerosol Jet Printing Conductive 3D Microstructures from Graphene Without Post‐Processing. Small, 20(12). https://doi.org/10.1002/smll.202305170

Vancouver

Smith BN, Ballentine P, Doherty JL, Wence R, Hobbie HA, Williams NX, et al. Aerosol Jet Printing Conductive 3D Microstructures from Graphene Without Post‐Processing. Small. 2024;20(12). doi:10.1002/smll.202305170

BibTeX
@article{Smith2024,
  author = {Smith, Brittany N and Ballentine, Peter and Doherty, James L and Wence, Ryan and Hobbie, Hansel Alex and Williams, Nicholas X and Franklin, Aaron D},
  title = {Aerosol Jet Printing Conductive 3D Microstructures from Graphene Without Post‐Processing},
  journal = {Small},
  year = {2024},
  volume = {20},
  number = {12},
  doi = {10.1002/smll.202305170}
}
Kostenlos starten →