EUVIMEDDescobrir EUVIMED
Crossref

High‐Performance CCF / PETG Filaments for Additive Manufacturing Prepared by Melt Impregnation

Jun Shi, Qifan Jiang, Shilong Zou, Yang Li, Zhixin Chen, Haoqian Liu, Lei Yang, Chunze Yan, Yusheng Shi

Polymer Composites · 2026-07-10 · 47 (13) · 12035-12053

DOI: 10.1002/pc.71075 ↗

At a glance

Journal article in Polymer Composites, published online on 2026-04-03. Written by Jun Shi and 8 co-authors. Cited 1 times so far (Crossref); 38 references. Funded by: Justis- og beredskapsdepartementet, National Natural Science Foundation of China, Natural Science Foundation of Hubei Province.

ResumoDados bibliográficosCiteRelated studies

Abstract (original language)

Continuous carbon fiber‐reinforced polymers (CCFRPs) exhibit superior mechanical properties compared with short‐fiber‐reinforced composites, while additive manufacturing (AM) enables the fabrication of complex geometries. Among various material systems, continuous carbon fiber‐reinforced polyethylene terephthalate glycol (CCF/PETG) produced by AM is particularly attractive due to its good processability and chemical resistance. In this work, a custom melt‐impregnation setup was developed to manufacture CCF/PETG prepreg filaments. The filament properties were systematically tuned by adjusting key processing parameters, especially impregnation temperature, impregnation pressure, and winding speed. By increasing the impregnation temperature and pressure while reducing the winding/stretching speed, stable forming and enhanced impregnation quality were achieved. Under optimized conditions, the prepared filaments reached a peak tensile strength of 1103.25 MPa, with a fiber volume fraction of 39.13%, a dense microstructure (porosity < 1%), and good geometric fidelity (circularity of 0.95). The practical printability of these filaments in fused deposition modeling (FDM) was further demonstrated: printed CCF/PETG components achieved a tensile strength of 715.16 MPa and a flexural strength of 457.44 MPa along the fiber direction. These results confirm that the proposed melt‐impregnation route can produce high‐quality continuous‐fiber thermoplastic feedstocks and enable the fabrication of high‐performance composites by AM.

Funding

  • Justis- og beredskapsdepartementet
  • National Natural Science Foundation of China
  • Natural Science Foundation of Hubei Province

Cite

APA

Shi, J., Jiang, Q., Zou, S., Li, Y., Chen, Z., Liu, H., Yang, L., Yan, C., & Shi, Y. (2026). High‐Performance CCF / PETG Filaments for Additive Manufacturing Prepared by Melt Impregnation. Polymer Composites, 47(13), 12035-12053. https://doi.org/10.1002/pc.71075

Vancouver

Shi J, Jiang Q, Zou S, Li Y, Chen Z, Liu H, et al. High‐Performance CCF / PETG Filaments for Additive Manufacturing Prepared by Melt Impregnation. Polymer Composites. 2026;47(13):12035-12053. doi:10.1002/pc.71075

BibTeX
@article{Shi2026,
  author = {Shi, Jun and Jiang, Qifan and Zou, Shilong and Li, Yang and Chen, Zhixin and Liu, Haoqian and Yang, Lei and Yan, Chunze and Shi, Yusheng},
  title = {High‐Performance CCF / PETG Filaments for Additive Manufacturing Prepared by Melt Impregnation},
  journal = {Polymer Composites},
  year = {2026},
  volume = {47},
  number = {13},
  pages = {12035--12053},
  doi = {10.1002/pc.71075}
}
Start for free →