EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Using Lignin and Spent Coffee Grounds as Bio‐Additives in 3D ‐Printable Poly Lactic Acid/Multi‐Walled Carbon Nanotube Composites for Advanced Electronic Applications

Silvia Lage‐Rivera, Ana Ares‐Pernas, M. Sonia Dopico‐García, Carlos M. Costa, Nelson Pereira, Senentxu Lanceros‐Mendez, María‐José Abad

Polymer Composites · 10.05.2026 · 47 (9) · 8261-8272

DOI: 10.1002/pc.70686 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Composites, online erschienen am 30.11.2025. Verfasst von Silvia Lage‐Rivera und 6 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Universidade da Coruña, Fundação para a Ciência e a Tecnologia, Eusko Jaurlaritza.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, three bio‐based additives, lignin, spent coffee grounds (SCG), and oil extracted from SCG (Ox‐SCG) were proposed as dispersant agents for multi‐walled carbon nanotubes (MWCNT) in a polylactic acid (PLA) matrix. The resulting materials' microstructure, degradation, thermal stability, rheological behavior, mechanical performance, electrical conductivity, and suitability for 3D printing (fused granular fabrication) were analyzed. The incorporation of the additives significantly strengthened the conductive network, while improving the material interlayer adhesion, especially with SCG. The electrical conductivity increased from 0.2E −1 S/cm (PLA/MWCNT) to 2.6E −1 S/cm (PLA/MWCNT/SCG). After studying the physical–chemical properties of the materials, functional strain gauges with two‐ and three‐arm geometries were 3D printed with the best formulation (PLA/MWCNT/SCG). Gauge factors of 0.23 and 1.03 were achieved for the two‐ and three‐arm designs, respectively, demonstrating increased sensitivity with added complexity. Finally, a proof of concept for an accelerometer was developed using the half‐bridge strain gauge setup, integrated with a custom electronic acquisition system.

Förderung

  • Universidade da Coruña
  • Fundação para a Ciência e a Tecnologia
  • Eusko Jaurlaritza

Zitieren

APA

Lage‐Rivera, S., Ares‐Pernas, A., Dopico‐García, M. S., Costa, C. M., Pereira, N., Lanceros‐Mendez, S., & Abad, M. (2026). Using Lignin and Spent Coffee Grounds as Bio‐Additives in 3D ‐Printable Poly Lactic Acid/Multi‐Walled Carbon Nanotube Composites for Advanced Electronic Applications. Polymer Composites, 47(9), 8261-8272. https://doi.org/10.1002/pc.70686

Vancouver

Lage‐Rivera S, Ares‐Pernas A, Dopico‐García MS, Costa CM, Pereira N, Lanceros‐Mendez S, et al. Using Lignin and Spent Coffee Grounds as Bio‐Additives in 3D ‐Printable Poly Lactic Acid/Multi‐Walled Carbon Nanotube Composites for Advanced Electronic Applications. Polymer Composites. 2026;47(9):8261-8272. doi:10.1002/pc.70686

BibTeX
@article{LageRivera2026,
  author = {Lage‐Rivera, Silvia and Ares‐Pernas, Ana and Dopico‐García, M. Sonia and Costa, Carlos M. and Pereira, Nelson and Lanceros‐Mendez, Senentxu and Abad, María‐José},
  title = {Using Lignin and Spent Coffee Grounds as Bio‐Additives in 3D ‐Printable Poly Lactic Acid/Multi‐Walled Carbon Nanotube Composites for Advanced Electronic Applications},
  journal = {Polymer Composites},
  year = {2026},
  volume = {47},
  number = {9},
  pages = {8261--8272},
  doi = {10.1002/pc.70686}
}
Kostenlos starten →