EUVIMEDOpdag EUVIMED
Open access · CC BY 4.0

Tuning the Properties of 3D‐Printed Electrochemical Devices by Using Different Fused Deposition Modeling Printers and Setups

Gennaro Persico iD, Panagiota M Kalligosfyri iD, Elena Lagreca iD, Vincenzo Ianniello iD, Concetta Di Natale, Michela Volgare, Antonio Cutolo iD, Filippo Defina, Waleed Alahmad iD, Abdulaziz K Assaifan iD, Mariarosaria Bucci, Stefano Cinti iD

ChemistryOpen · 2026-10 · 15 (10)

DOI: 10.1002/open.70303 ↗

At a glance

Journal article in ChemistryOpen, published online on 2026-09-24. Written by Gennaro Persico and 11 co-authors. Institution: Department of Pharmacy, University of Naples Federico II, Naples, Italy. Cited 1 times so far (Crossref); 55 references. The full text is freely available (open access, CC BY 4.0). Funded by: Royal Society of Chemistry, Regione Campania, AIRC - MFAG 2022 project.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Although fused deposition modeling (FDM) 3D printing has emerged as an accessible and versatile approach for the fabrication of electrochemical sensors, the type of printer and manufacturing setup might affect the quality of the ultimate device. In this work, the electrochemical performance of conductive polylactic acid (PLA)‐based printed sensors have been tuned by interrogating different cost classes and hardware configurations. Electrochemical behavior was investigated using cyclic voltammetry with both inner‐ and outer‐sphere redox probes, namely potassium ferricyanide (III) and hexaammineruthenium (III) chloride, to evaluate surface accessibility and electron‐transfer properties. Scanning electron microscopy and tensile tests were additionally performed to characterize electrode morphology and mechanical stability. Among the evaluated 3D printers, high‐performance systems characterized by higher automation, improved motion control, and greater extrusion stability demonstrated satisfactory outcomes. In contrast, entry‐level open‐platform systems showed lower surface utilization and reduced electrochemical performance. The results demonstrate that all printing platforms were capable of producing sensors with electrochemical functionality, comparable mechanical properties, and well‐defined architectures. However, despite negligible differences among PLA filaments, it is clear that printing time, automation, and hardware flexibility represent central factors in selecting the most suitable platform for next scaling of electrode manufacturing.

Subjects

Author keywords

3D‐printed device3D‐printingadditive manufacturingcharacterizationelectrochemical sensors

Authors and institutions

  • Department of Pharmacy, University of Naples Federico II, Naples, Italy.
  • Dipartimento di Ingegneria Chimica, dei Materiali e della Produzione Industriale, University of Naples Federico II, Naples, Italy.
  • 3DnA s.r.l., Naples, Italy.
  • Department of Chemistry, Faculty of Science, Chulalongkorn University, Bangkok, Thailand.
  • Biomedical Technology Department, College of Applied Medical Sciences, King Saud University, Riyadh, Saudi Arabia.
  • Sbarro Institute for Cancer Research and Molecular Medicine, Center for Biotechnology, College of Science and Technology, Temple University, Philadelphia, Pennsylvania, USA.

ORCID profiles: Gennaro Persico, Panagiota M Kalligosfyri, Elena Lagreca, Vincenzo Ianniello, Antonio Cutolo, Waleed Alahmad, Abdulaziz K Assaifan, Stefano Cinti

Funding

  • Royal Society of Chemistry
  • Regione Campania
  • AIRC - MFAG 2022 project
  • King Saud University

Cite

APA

Persico, G., Kalligosfyri, P. M., Lagreca, E., Ianniello, V., Natale, C. D., Volgare, M., Cutolo, A., Defina, F., Alahmad, W., Assaifan, A. K., Bucci, M., & Cinti, S. (2026). Tuning the Properties of 3D‐Printed Electrochemical Devices by Using Different Fused Deposition Modeling Printers and Setups. ChemistryOpen, 15(10). https://doi.org/10.1002/open.70303

Vancouver

Persico G, Kalligosfyri PM, Lagreca E, Ianniello V, Natale CD, Volgare M, et al. Tuning the Properties of 3D‐Printed Electrochemical Devices by Using Different Fused Deposition Modeling Printers and Setups. ChemistryOpen. 2026;15(10). doi:10.1002/open.70303

BibTeX
@article{Persico2026,
  author = {Persico, Gennaro and Kalligosfyri, Panagiota M and Lagreca, Elena and Ianniello, Vincenzo and Natale, Concetta Di and Volgare, Michela and Cutolo, Antonio and Defina, Filippo and Alahmad, Waleed and Assaifan, Abdulaziz K and Bucci, Mariarosaria and Cinti, Stefano},
  title = {Tuning the Properties of 3D‐Printed Electrochemical Devices by Using Different Fused Deposition Modeling Printers and Setups},
  journal = {ChemistryOpen},
  year = {2026},
  volume = {15},
  number = {10},
  doi = {10.1002/open.70303}
}
Start for free →