EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Successive Mechanical Recycling of Poly(lactic Acid) by Injection Molding: Evolution of Molecular, Thermal, and Mechanical Properties

László Lendvai, Virág Luca Bódi, Martin Danko, Petar Sabev Varbanov, Sándor Kálmán Jakab

Macromolecular Materials and Engineering · 2026-03 · 311 (3)

DOI: 10.1002/mame.202500349 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Materials and Engineering, online erschienen am 21.11.2025. Verfasst von László Lendvai und 4 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 71 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research, Development and Innovation Office, Vedecká Grantová Agentúra MŠVVaŠ SR a SAV.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the changes in the molecular structure, as well as the thermal and mechanical properties of poly‐lactic‐acid (PLA), during successive closed‐loop mechanical recycling through injection molding. Gel permeation chromatographic (GPC) analyses revealed a gradual decrease in molar mass (MM); after ten recycling steps, the MM of PLA was reduced to one‐third of its initial value. According to differential scanning calorimetric (DSC) measurements, both the glass transition temperature and the cold crystallization temperature of PLA decreased, while the crystallization was facilitated by the successive recycling steps. This was ascribed to the improved chain mobility resulting from the reduced MM. Quasi‐static mechanical properties were evaluated using tensile tests, while impact toughness was assessed through Charpy tests. The tensile strength of PLA was not significantly affected by recycling until the fifth recycling step, where it suffered a slight (∼5%) reduction. Meanwhile, Young's modulus, elongation at yield, and impact strength remained approximately the same as the freshly injected sample at that point. However, after ten recycling steps, all analyzed properties declined significantly: Young's modulus by 11%, tensile strength by 68%, elongation at yield by 63%, and impact strength by 30%.

Förderung

  • National Research, Development and Innovation Office
  • Vedecká Grantová Agentúra MŠVVaŠ SR a SAV

Zitieren

APA

Lendvai, L., Bódi, V. L., Danko, M., Varbanov, P. S., & Jakab, S. K. (2026). Successive Mechanical Recycling of Poly(lactic Acid) by Injection Molding: Evolution of Molecular, Thermal, and Mechanical Properties. Macromolecular Materials and Engineering, 311(3). https://doi.org/10.1002/mame.202500349

Vancouver

Lendvai L, Bódi VL, Danko M, Varbanov PS, Jakab SK. Successive Mechanical Recycling of Poly(lactic Acid) by Injection Molding: Evolution of Molecular, Thermal, and Mechanical Properties. Macromolecular Materials and Engineering. 2026;311(3). doi:10.1002/mame.202500349

BibTeX
@article{Lendvai2026,
  author = {Lendvai, László and Bódi, Virág Luca and Danko, Martin and Varbanov, Petar Sabev and Jakab, Sándor Kálmán},
  title = {Successive Mechanical Recycling of Poly(lactic Acid) by Injection Molding: Evolution of Molecular, Thermal, and Mechanical Properties},
  journal = {Macromolecular Materials and Engineering},
  year = {2026},
  volume = {311},
  number = {3},
  doi = {10.1002/mame.202500349}
}
Kostenlos starten →