High‐Impact PLA in Compatibilized PLA/PCL Blends: Optimization of Blend Composition and Type and Content of Compatibilizer
Macromolecular Materials and Engineering · 2023-12 · 308 (12)
DOI: 10.1002/mame.202300213 ↗Kurz gefasst
Fachartikel in der Zeitschrift Macromolecular Materials and Engineering, online erschienen am 22.09.2023. Verfasst von Ainhoa Fernández‐Tena und 6 weiteren Autor:innen. Die Arbeit wurde bisher 34-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Eusko Jaurlaritza, Ministerio de Ciencia e Innovación.
Abstract (Originalsprache)
In this work, the effectiveness of seven commercial compatibilizers is tested in polylactide (PLA)/poly(ε‐caprolactone) (PCL) blends with different compositions to obtain a high‐impact PLA. None of the compatibilizers is effective for 90/10 and 80/20 PLA/PCL compositions, as no improvement of the impact strength is observed. For the 70/30 composition, compatibilizers having glycidyl methacrylate (GMA) and acrylate groups in their structure are proved the most effective, as the morphological change towards co‐continuity induced by them leads to significant impact strength improvements (of ≈345% and 90% with respect to the neat PLA and the noncompatibilized PLA/PCL 70/30 blend, respectively). The 70/30 PLA/PCL composition, as it shows the best balance of properties, and the best compatibilizer (ElvaloyPTW) are chosen to carry out the optimization of the compatibilizer content. It is found that adding 6 phr to the blend results in highly toughened and ductile blends while maintaining a high modulus and yield strength values. Larger compatibilizer contents lead to even higher impact strength values, but the low‐strain mechanical properties are notably reduced. Thus, in this work, a simple and easily scalable method to produce high‐impact PLA is shown, as it implies the compounding of three commercially available components without involving any toxic solvents.
Förderung
- Eusko Jaurlaritza
- Ministerio de Ciencia e Innovación
Zitieren
APA
Fernández‐Tena, A., Otaegi, I., Irusta, L., Sebastián, V., Guerrica‐Echevarria, G., Müller, A. J., & Aranburu, N. (2023). High‐Impact PLA in Compatibilized PLA/PCL Blends: Optimization of Blend Composition and Type and Content of Compatibilizer. Macromolecular Materials and Engineering, 308(12). https://doi.org/10.1002/mame.202300213
Vancouver
Fernández‐Tena A, Otaegi I, Irusta L, Sebastián V, Guerrica‐Echevarria G, Müller AJ, et al. High‐Impact PLA in Compatibilized PLA/PCL Blends: Optimization of Blend Composition and Type and Content of Compatibilizer. Macromolecular Materials and Engineering. 2023;308(12). doi:10.1002/mame.202300213
BibTeX
@article{FernndezTena2023,
author = {Fernández‐Tena, Ainhoa and Otaegi, Itziar and Irusta, Lourdes and Sebastián, Victor and Guerrica‐Echevarria, Gonzalo and Müller, Alejandro Jesus and Aranburu, Nora},
title = {High‐Impact PLA in Compatibilized PLA/PCL Blends: Optimization of Blend Composition and Type and Content of Compatibilizer},
journal = {Macromolecular Materials and Engineering},
year = {2023},
volume = {308},
number = {12},
doi = {10.1002/mame.202300213}
}
EUVIMED