In Situ Compatibilized Blends of PLA/PCL/CAB Melt-Blown Films with High Elongation: Investigation of Miscibility, Morphology, Crystallinity and Modelling
Polymers · 06.01.2023 · 15 (2) · 303
DOI: 10.3390/polym15020303 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 06.01.2023. Verfasst von Nantaprapa Tuancharoensri und 11 weiteren Autor:innen. Beteiligte Einrichtung: Biopolymer Group, Department of Chemistry, Faculty of Science, Naresuan University, Phitsanulok 65000, Thailand. Die Arbeit wurde bisher 36-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Ternary-blended, melt-blown films of polylactide (PLA), polycaprolactone (PCL) and cellulose acetate butyrate (CAB) were prepared from preliminary miscibility data using a rapid screening method and optical ternary phase diagram (presented as clear, translucent, and opaque regions) as a guide for the composition selection. The compositions that provided optically clear regions were selected for melt blending. The ternary (PLA/PCL/CAB) blends were first melt-extruded and then melt-blown to form films and characterized for their tensile properties, tensile fractured-surface morphology, miscibility, crystallinity, molecular weight and chemical structure. The results showed that the tensile elongation at the break (%elongation) of the ternary-blended, melt-blown films (85/5/10, 75/10/15, 60/15/25 of PLA/PCL/CAB) was substantially higher (>350%) than pure PLA (ca. 20%). The range of compositions in which a significant increase in %elongation was observed at 55–85% w/w PLA, 5–20% w/w PCL and 10–25% w/w CAB. Films with high %elongation all showed good interfacial interactions between the dispersed phase (PCL and CAB) and matrix (PLA) in FE-SEM and showed improvements in miscibility (higher intermolecular interaction and mixing) and a decrease in the glass transition temperature, when compared to the low %elongation films. The decrease in Mw and Mn and the formation of the new NMR peaks (1H NMR at 3.68–3.73 ppm and 13C NMR at 58.54 ppm) were observed in only the high %elongation films. These are expected to be in situ compatibilizers that are generated during the melt processing, mostly by chain scission. In addition, mathematical modelling was used to study the optimal ratio and cost-effectiveness of blends with optimised mechanical properties. These ternary-blended, melt-blown films have the potential for use in both packaging and medical devices with excellent mechanical performance as well as inherent economic and environmental capabilities.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Biopolymer Group, Department of Chemistry, Faculty of Science, Naresuan University, Phitsanulok 65000, Thailand.
- Center of Excellence in Biomaterials, Faculty of Science, Naresuan University, Phitsanulok 65000, Thailand.
- Department of Pharmaceutical Technology, Faculty of Pharmaceutical Sciences, Naresuan University, Phitsanulok 65000, Thailand.
- Center of Excellence for Innovation in Chemistry, Naresuan University, Phitsanulok 65000, Thailand.
- Department of Mathematics, Faculty of Science, Naresuan University, Phitsanulok 65000, Thailand.
- Center of Excellence in Nonlinear Analysis and Optimization, Faculty of Science, Naresuan University, Phitsanulok 65000, Thailand.
ORCID-Profile: Gareth M Ross, Narin Petrot, Paul D Topham, Sukunya Ross
Zitieren
APA
Tuancharoensri, N., Ross, G. M., Kongprayoon, A., Mahasaranon, S., Pratumshat, S., Viyoch, J., Petrot, N., Ruanthong, W., Punyodom, W., Topham, P. D., Tighe, B. J., & Ross, S. (2023). In Situ Compatibilized Blends of PLA/PCL/CAB Melt-Blown Films with High Elongation: Investigation of Miscibility, Morphology, Crystallinity and Modelling. Polymers, 15(2), 303. https://doi.org/10.3390/polym15020303
Vancouver
Tuancharoensri N, Ross GM, Kongprayoon A, Mahasaranon S, Pratumshat S, Viyoch J, et al. In Situ Compatibilized Blends of PLA/PCL/CAB Melt-Blown Films with High Elongation: Investigation of Miscibility, Morphology, Crystallinity and Modelling. Polymers. 2023;15(2):303. doi:10.3390/polym15020303
BibTeX
@article{Tuancharoensri2023,
author = {Tuancharoensri, Nantaprapa and Ross, Gareth M and Kongprayoon, Arisa and Mahasaranon, Sararat and Pratumshat, Supatra and Viyoch, Jarupa and Petrot, Narin and Ruanthong, Wuttipong and Punyodom, Winita and Topham, Paul D and Tighe, Brian J and Ross, Sukunya},
title = {In Situ Compatibilized Blends of PLA/PCL/CAB Melt-Blown Films with High Elongation: Investigation of Miscibility, Morphology, Crystallinity and Modelling},
journal = {Polymers},
year = {2023},
volume = {15},
number = {2},
pages = {303},
doi = {10.3390/polym15020303}
}
EUVIMED