Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification
Journal of Foot and Ankle Research · 2026-06 · 19 (2)
DOI: 10.1002/jfa2.70174 ↗At a glance
Randomisierte kontrollierte Studie in Journal of Foot and Ankle Research, published online on 2026-06-22. Written by Ziang Jiang and 6 co-authors. Institution: Institute for Biomechanics, ETH Zürich, Zürich, Switzerland. Major MEDLINE topics: Shoes, Gait, Osteoarthritis, Knee, Printing, Three-Dimensional. 44 references. The full text is freely available (open access, CC BY 4.0). Funded by: Innosuisse - Schweizerische Agentur für Innovationsförderung.
Abstract (original language)
Introduction
To evaluate whether a 3D‐printed shoe sole can passively replicate toe‐out gait biomechanics and reduce the knee adduction moment (KAM) and knee adduction angular impulse (KAAI), addressing limitations of traditional gait retraining.
Methods
Custom shoe soles were 3D‐printed using gyroid infill structures to create a rotational hind‐sole and a variable stiffness fore‐sole (‘RVS’ shoes). Twenty‐one healthy adults completed three baseline gait trials in control shoes, followed by randomised biofeedback‐based gait retraining at toe‐out angles of 5°, 10° and 15°. After each retraining session, motion capture was used during overground walking. Participants then walked wearing RVS shoes for three trials. Gait biomechanics were analysed using repeated measures ANOVA and multiple linear regression.
Results
Compared to baseline, KAM's second peak was significantly reduced after toe‐out retraining: 5° (13.6%, p = 0.002), 10° (20.2%, p < 0.001) and 15° (31.7%, p < 0.001). RVS shoes alone reduced it by 16.3% ( p < 0.001), and KAAI by 8.6% ( p < 0.001)—a reduction not achieved by retraining. Regression analysis showed that changes in KAM were strongly predicted (95%) by knee centre‐of‐pressure offset and mediolateral ground reaction force.
Conclusion
3D‐printed RVS shoes passively replicated or exceeded the biomechanical effects of active toe‐out gait retraining, offering a promising, low‐effort intervention for managing knee osteoarthritis.
Subjects
MeSH terms (MEDLINE)
Author keywords
Authors and institutions
- Institute for Biomechanics, ETH Zürich, Zürich, Switzerland.
- Swissbiomechanics AG, Einsiedeln, Switzerland.
- Institute of Social and Preventive Medicine, University of Bern, Bern, Switzerland.
- Department of Rheumatology and Immunology, Inselspital, Bern University Hospital, University of Bern, Bern, Switzerland.
ORCID profiles: William R Taylor
Funding
- Innosuisse - Schweizerische Agentur für Innovationsförderung
Cite
APA
Jiang, Z., Studer, P. B., Zäh, M., Kryenbühl, C., Reichenbach, S., Taylor, W. R., & Zhang, Q. (2026). Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification. Journal of Foot and Ankle Research, 19(2). https://doi.org/10.1002/jfa2.70174
Vancouver
Jiang Z, Studer PB, Zäh M, Kryenbühl C, Reichenbach S, Taylor WR, et al. Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification. Journal of Foot and Ankle Research. 2026;19(2). doi:10.1002/jfa2.70174
BibTeX
@article{Jiang2026,
author = {Jiang, Ziang and Studer, Paciane Bo and Zäh, Matthias and Kryenbühl, Christian and Reichenbach, Stephan and Taylor, William R and Zhang, Qiang},
title = {Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification},
journal = {Journal of Foot and Ankle Research},
year = {2026},
volume = {19},
number = {2},
doi = {10.1002/jfa2.70174}
}
EUVIMED