EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D-Printed Insole for Measuring Ground Reaction Force and Center of Pressure During Walking

Le Tung Vu iD, Joel Bottin-Noonan iD, Lucy Armitage iD, Gursel Alici iD, Manish Sreenivasa iD

Sensors · 17.04.2025 · 25 (8) · 2524

DOI: 10.3390/s25082524 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 17.04.2025. Verfasst von Le Tung Vu und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical, Materials, Mechatronic and Biomedical Engineering, Faculty of Engineering and Information Sciences, University of Wollongong, W…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Walking. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: University of Wollongong.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ground reaction force (GRF) and center of pressure (COP) during walking are two important measures that could be used in a range of applications, from the control of devices such as exoskeletons to clinical assessments. Recording these measures requires fixed laboratory equipment such as force plates or expensive portable insoles. We present an alternative approach by developing a 3D-printed insole that uses pneumatic chambers and pressure sensors to estimate the net GRF and the anterior–posterior COP position. The intentionally simple design, using just two pneumatic chambers, can be fabricated using standard 3D printing technology and readily available soft materials. We used experimentally recorded data from a motion capture system along with parameter identification techniques to characterize and validate the insole while walking at different speeds. Our results showed that the insole was capable of withstanding repeated loading during walking—up to 1.2 times the body weight—and possessed a bandwidth high enough to capture gait dynamics. The identified models could estimate the GRF and the anterior–posterior COP position with less than 9% error. These results compare favourably with those of commercially available instrumented insoles and can be obtained at a fraction of their cost. This low-cost yet effective solution could assist in applications where it is important to record gait outside of laboratory conditions, but the cost of commercial solutions is prohibitive.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalWalkingHumansGaitPressureBiomechanical PhenomenaEquipment DesignShoes

Stichwörter der Autor:innen

biomechanicsfoot forceskineticsplantar pressurewearable sensors

Autor:innen und Institutionen

  • School of Mechanical, Materials, Mechatronic and Biomedical Engineering, Faculty of Engineering and Information Sciences, University of Wollongong, Wollongong, NSW 2522, Australia.

ORCID-Profile: Le Tung Vu, Joel Bottin-Noonan, Lucy Armitage, Gursel Alici, Manish Sreenivasa

Förderung

  • University of Wollongong

Zitieren

APA

Vu, L. T., Bottin-Noonan, J., Armitage, L., Alici, G., & Sreenivasa, M. (2025). 3D-Printed Insole for Measuring Ground Reaction Force and Center of Pressure During Walking. Sensors, 25(8), 2524. https://doi.org/10.3390/s25082524

Vancouver

Vu LT, Bottin-Noonan J, Armitage L, Alici G, Sreenivasa M. 3D-Printed Insole for Measuring Ground Reaction Force and Center of Pressure During Walking. Sensors. 2025;25(8):2524. doi:10.3390/s25082524

BibTeX
@article{Vu2025,
  author = {Vu, Le Tung and Bottin-Noonan, Joel and Armitage, Lucy and Alici, Gursel and Sreenivasa, Manish},
  title = {3D-Printed Insole for Measuring Ground Reaction Force and Center of Pressure During Walking},
  journal = {Sensors},
  year = {2025},
  volume = {25},
  number = {8},
  pages = {2524},
  doi = {10.3390/s25082524}
}
Kostenlos starten →